Atec Tektronix-1502 - Manual (Page 99)

TM 9-4935-601-14-3&P
SECTION 9
REPLACEABLE
MECHANICAL PARTS
PARTS ORDERING INFORMATION
Replacement parts are available from or through your local Tektronix, Inc. Field Office or representative.
Changes to Tektronix instruments are sometimes made to accommodate improved components as they become available, and to give you the
benefit of the latest circuit improvements developed in our engineering department. It is therefore important, when ordering parts, to include the
following information in your order: Part number, instrument type or number, serial number, and modification number if applicable.
If a part you have ordered has been replaced with a new or improved part, your local Tektronix, Inc. Field Office or representative will contact
you concerning any change in part number.
Change information, if any, is located at the rear of this manual.
SPECIAL NOTES AND SYMBOLS
X000 Part first added at this serial number
00X Part removed after this serial number
FIGURE AND INDEX NUMBERS
Items in this section are referenced by figure and index numbers to the illustrations.
INDENTATION SYSTEM
This mechanical parts list is indented to indicate item relationships. Following is an example of the indentation system used in the description
column.
1 2 3 4 5 Name & Description
Assembly and/or Component
Attaching parts for Assembly and/or Component
Detail Part of Assembly and/or Component
Attaching parts for Detail Part
Parts of Detail Part
Attaching parts for Parts of Detail Part
Attaching Parts always appear in the same indentation as the item it mounts, while the detail parts are indented to the right. Indented items
are part of, and included with, the next higher indentation. The separation symbol - - - ' - - - indicates the end of attaching parts.
Attaching parts must be purchased separately, unless otherwise specified.
ITEM NAME
In the Parts List, an Item Name is separated from the description by a colon (:). Because of space limitations, an Item Name may sometimes
appear as incomplete. For further Item Name identification, the U.S. Federal Cataloging Handbook H6-1 can be utilized where possible.
ABBREVIATIONS
INCH ELCTRN ELECTRON IN INCH SE SINGLE END
# NUMBER SIZE ELEC ELECTRICAL INCAND INCANDESCENT SECT SECTION
ACTR ACTUATOR ELCTLT ELECTROLYTIC INSUL INSULATOR SEMICOND SEMICONDUCTOR
ADPTR ADAPTER ELEM ELEMENT INTL INTERNAL SHLD SHIELD
ALIGN ALIGNMENT EPL ELECTRICAL PARTS LISTLPHLDR LAMPHOLDER SHLDR SHOULDERED
AL ALUMINUM EQPT EQUIPMENT MACH MACHINE SKT SOCKET
ASSEM ASSEMBLED EXT EXTERNAL MECH MECHANICAL SL SLIDE
ASSY ASSEMBLY FIL FILLISTER HEAD MTG MOUNTING SLFLKG SELF-LOCKING
ATTEN ATTENUATOR FLEX FLEXIBLE NIP NIPPLE SLVG SLEEVING
AWG AMERICAN WIRE GAGE FLH FLAT HEAD NON WIRE NOT WIRE WOUND SPR SPRING
BD BOARD FLTR FILTER OBD ORDER BY DESCRIPTIONSQ SQUARE
BRKT BRACKET FR FRAME or FRONT OD OUTSIDE DIAMETER SST STAINLESS STEEL
BRS BRASS FSTNR FASTENER OVH OVAL HEAD STL STEEL
BRZ BRONZE FT FOOT PH BRZ PHOSPHOR BRONZE SW SWITCH
BSHG BUSHING FXD FIXED PL PLAIN or PLATE T TUBE
CAB CABINET GSKT GASKET PLSTC PLASTIC TERM TERMINAL
CAP CAPACITOR HDL HANDLE PN PART NUMBER THD THREAD
CER CERAMIC HEX HEXAGON PNH PAN HEAD THK THICK
CHAS CHASSIS HEX HD HEXAGONAL HEAD PWR POWER TNSN TENSION
CKT CIRCUIT HEX SOC HEXAGONAL SOCKET RCPT RECEPTACLE TPG TAPPING
COMP COMPOSITION HLCPS HELICAL COMPRESSIONRES RESISTOR TRH TRUSS HEAD
CONN CONNECTOR HLEXT HELICAL EXTENSION RGD RIGID V VOLTAGE
COV COVER HV HIGH VOLTAGE RLF RELIEF VAR VARIABLE
CPLG COUPLING IC INTEGRATED CIRCUIT RTNR RETAINER W/ WITH
CRT CATHODE RAY TUBE ID INSIDE DIAMETER SCH SOCKET HEAD WSHR WASHER
DEG DEGREE IDENT IDENTIFICATION SCOPE OSCILLOSCOPE XFMR TRANSFORMER
DWR DRAWER IMPLR IMPELLER SCR SCREW XSTR TRANSISTOR
9-1