Atec Agilent-E8361A - Manual (Page 40)

0
E8361A
Test port input
continued
Description Specification Option UNL Supplemental
Standard or Option 014 and Option 014 information
Third Order Intercept 1 – Tone spacing from 100 kHz to 5 MHz
Typical:
10 to 500 MHz +0 dBm
500 MHz to GHz + dBm
to 0 GHz + dBm
0 to 50 GHz + dBm
50 to 67 GHz +6 dBm
Third Order Intercept 1 – Tone spacing from 5 to 20 MHz
Typical:
10 to 500 MHz Not applicable
500 MHz to GHz +0 dBm
to 0 GHz +0 dBm
0 to 50 GHz + dBm
50 to 67 GHz + dBm
Third Order Intercept 1 – Tone spacing from 20 to 50 MHz
Typical:
10 to 500 MHz Not applicable
500 MHz to GHz +6 dBm
to 0 GHz + dBm
0 to 50 GHz +5 dBm
50 to 67 GHz +7 dBm
System compression level – at maximum leveled output power
See Dynamic Accuracy Chart
Trace noise magnitude
10 to 5 MHz < 0.150 dB rms < 0.150 dB rms
5 to 500 MHz , 5 < 0.010 dB rms < 0.010 dB rms 1 kHz IF bandwidth
500 MHz to GHz < 0.006 dB rms < 0.006 dB rms ratio measurement, nominal
to 67 GHz < 0.006 dB rms < 0.009 dB rms power at test port
67 to 70 GHz < 0.006 dB rms < 0.009 dB rms
Trace noise magnitude 2 – Option 080 enabled 3
10 to 5 MHz < 0.150 dB rms < 0.150 dB rms
5 to 500 MHz , 5 < 0.010 dB rms < 0.010 dB rms 1 kHz IF bandwidth
500 MHz to GHz < 0.006 dB rms < 0.006 dB rms ratio measurement, nominal
to 67 GHz < 0.009 dB rms < 0.01 dB rms power at test port
67 to 70 GHz < 0.009 dB rms < 0.01 dB rms
Trace noise phase
10 to 5 MHz < 0.800° rms < 0.800° rms
5 to 500 MHz 5 < 0.100° rms < 0.100° rms 1 kHz IF bandwidth
500 MHz to GHz < 0.060° rms < 0.060° rms ratio measurement, nominal
to 67 GHz < 0.100° rms < 0.100° rms power at test port
67 to 70 GHz < 0.100° rms < 0.100° rms
Trace noise phase 2 – Option 080 enabled 3
10 to 5 MHz < 0.800° rms < 0.800° rms 1 kHz IF bandwidth
5 to 500 MHz 5 < 0.100° rms < 0.100° rms ratio measurement, nominal
500 MHz to GHz < 0.060° rms < 0.060° rms power at test port
to 67 GHz < 0.100° rms < 0.100° rms
67 to 70 GHz < 0.100° rms < 0.100° rms
1. Third order intercept is a typical specification that applies while the network
analyzer receiver is in its linear range.
. Typical performance.
. 0 Hz offset.
. Trace noise magnitude may be degraded to 0 mdB rms at harmonic frequencies
of the first IF (8. MHz) below 80 MHz.
5. Specified value is for worst-case noise floor at 5 MHz.