Atec Agilent-E8361A - Manual (Page 39)

9
E8361A
Test port input
continued
Description Specification Option 014 or Supplemental
Standard Option 014 and UNL (typ.) information
Direct receiver access
input noise floor 1
10 Hz IF bandwidth
10 to 5 MHz < -106 dBm
5 to 500 MHz , 5 < -105 dBm Online Help also includes the
500 MHz to GHz < -15.5 dBm category “Direct receiver access
to 10 GHz < -15 dBm input noise floor, Option 080 enabled”
10 to GHz < -18 dBm
to 0 GHz < -117.5 dBm
0 to 0 GHz < -117 dBm Option 016 degrades
0 to 5 GHz < -115 dBm performance by dB.
5 to 50 GHz < -11.5 dBm
50 to 60 GHz < -111 dBm
60 to 67 GHz < -108 dBm Option 016 degrades
67 to 70 GHz < -107 dBm performance by dB.
1 kHz IF bandwidth
10 to 5 MHz < -86 dBm
5 to 500 MHz , 5 < -85 dBm
500 MHz to GHz < -105.5 dBm
to 10 GHz < -105 dBm
10 to GHz < -108 dBm
to 0 GHz < -97.5 dBm
0 to 0 GHz < -97 dBm Option 016 degrades
0 to 5 GHz < -95 dBm performance by dB.
5 to 50 GHz < -9.5 dBm
50 to 60 GHz < -91 dBm
60 to 67 GHz < -88 dBm Option 016 degrades
67 to 70 GHz < -87 dBm performance by dB.
Description Specification Supplemental
Receiver compression level (measured at Test Ports)
Supplemental
Specifications Information
Standard Option 014 Option 014 and UNL Typical
10 to 5 MHz , negligible negligible negligible negligible
5 to 500 MHz , 6 <0.1 dB at -9.5 dBm 7 <0.1 dB at -9.5 dBm 7 <0.1 dB at -9.5 dBm 7 <0.1 dB at +0.5 dBm 7
and <0.5 dB at - dBm and <0.5 dB at - dBm and <0.5 dB at - dBm and <0.5 dB at +8 dBm
500 MHz to 5 GHz <0.1 dB at -8 dBm 7 <0.1 dB at -8 dBm 7 <0.1 dB at -7 dBm 7 <0.1 dB at - dBm 7
and <0.5 dB at -1 dBm and <0.5 dB at -1 dBm and <0.5 dB at 0 dBm and <0.5 dB at + dBm
5 to 0 GHz <0.1 dB at -8.5 dBm 7 <0.1 dB at -8.5 dBm 7 <0.1 dB at -6 dBm 7 <0.1 dB at -1 dBm 7
and <0.5 dB at - dBm and <0.5 dB at - dBm and <0.5 dB at +1 dBm and <0.5 dB at +6 dBm
0 to 67 GHz < 0.1 dB at -10.5 dBm 7 < 0.1 dB at -8 dBm 7 <0.1 dB at –9.5 dBm 7 <0.1 dB at - dBm 7, 8
and <0.15 dB at -7 dBm and <0.15 dB at - dBm and <0.15 dB at -6 dBm and <0.15 dB at + dBm 8
67 to 70 GHz <0.1 dB at - dBm 7, 8
and <0.15 dB at + dBm 8
1. Total average (rms) noise power calculated as mean value of a linear magnitude
trace expressed in dBm.
. Typical performance.
. Coupler roll-off will reduce compression to a negligible level below 500 MHz.
. Noise floor may be degraded by 10 dB at particular frequencies
(multiples of 5 MHz) due to spurious receiver residuals.
5. Specified value is for worst-case noise floor at 5 MHz.
6. Specified value is for worst-case compression at 500 MHz.
7. This compression level comes from the dynamic accuracy curve with -0 dBm
reference test port power.
8. Option 016 degrades performance by dB.