Atec Agilent-E8361A - Manual (Page 13)

1
E8362/3/4B
Test port output
Description Specification Supplemental information
Standard 014 UNL UNL and 014
Frequency range
E86B 10 MHz to 0 GHz
E86B 10 MHz to 0 GHz
E86B 10 MHz to 50 GHz
Nominal power
2
E86B 0 dBm -5 dBm -5 dBm -5 dBm
E86/B -1 dBm -17 dBm -17 dBm -17 dBm
Frequency resolution 1 Hz 1 Hz 1 Hz 1 Hz
CW accuracy ± 1ppm ± 1ppm ± 1ppm ± 1ppm
Frequency stability ±1 ppm, 0 to 0 °C, typical
±0. ppm/yr, typical
Power level accuracy 1
10 to 5 MHz ±.0 dB ±.0 dB ±.0 dB ±.0 dB
5 MHz to 10 GHz ±1.5 dB ±1.5 dB ±1.5 dB ±1.5 dB Variation from nominal
10 to 0 GHz ±.0 dB ±.0 dB ±.0 dB ±.0 dB power in range 0
0 to 0 GHz ±.0 dB ±.0 dB ±.0 dB ±.0 dB (step attenuator at 0 dB).
0 to 5 GHz ±.0 dB ±.5 dB ±.0 dB ±.5 dB
5 to 50 GHz ±.0 dB ±.0 dB ±.0 dB ±.0 dB
Power level linearity 6
10 to 5 MHz ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB
5 MHz to 0 GHz ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB Test reference is at the
0 to 0 GHz ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB nominal power level
0 to 50 GHz ±1.0 dB ±1.0 dB ±1.0 dB ±1.0 dB (step attenuator at 0 dB).
Power range 1, 5, 7
10 to 5 MHz -5 to + dB -5 to + dBm -87 to + dBm -87 to + dBm
5 MHz to 10 GHz -5 to +5 dB -5 to +5 dBm -87 to + dBm -87 to + dBm 8
10 to 0 GHz - to + dB -5 to + dBm -86 to +1 dBm -87 to 0 dBm 9
0 to 0 GHz - to 0 dBm -5 to - dBm -85 to - dBm -87 to - dBm
0 to 0 GHz - to - dBm -5 to - 6 dBm -85 to -6 dBm -87 to -8 dBm
0 to 5 GHz -5 to -5 dBm -7 to -7 dBm -87 to -9 dBm -87 to -11 dBm
5 to 50 GHz -5 to -10 dBm -7 to -1 dBm -87 to -15 dBm -87 to -17 dBm
Power sweep range (ALC)
10 to 5 MHz 7 dB 7 dB 9 dB 9 dB
5 MHz to 10 GHz 0 dB 0 dB 0 dB 0 dB 10 ALC range starts at
10 to 0 GHz 7 dB 7 dB 7 dB 7 dB 11 maximum leveled output
0 to 0 GHz dB dB dB dB power and decreases by
0 to 0 GHz 19 dB 19 dB 19 dB 19 dB power level indicated in
0 to 5 GHz 0 dB 0 dB 18 dB 16 dB the table.
5 to 50 GHz 15 dB 15 dB 1 dB 10 dB
Power resolution 0.01 dB 0.01 dB 0.01 dB 0.01 dB
1. Test port output is a specification when the source is set to port 1 and a
characteristic when the source is set to port .
. Preset power.
. Typical performance.
. ±1.5 dB for power ≤ - dBm.
5. Power to which the source can be set and phase lock is assured.
6. Power level linearity is a specification when the source is set to port 1 and a
typical when the source is set to port .
7. Test port power is specified into nominal 50 ohms.
8. Option H11 decreases maximum power level by 1 dB.
9. Option H11 decreases maximum power level by dB.
10. Option H11 decreases power level by 1 dB.
11. Option H11 decreases power level by dB.