Atec Agilent-E8361A - Manual (Page 38)

8
E8361A
Test port input
Description Specification Option 014 or Option 016 Supplemental
Standard Option UNL and 014 information
Test port noise floor 1 080 enabled, 5 typical
10 Hz IF bandwidth
10 to 5 MHz < -70 dBm < -70 dBm < -70 dBm < -70 dBm
5 to 500 MHz , < -90 dBm < -90 dBm < -90 dBm < -90 dBm
500 MHz to GHz < -11 dBm < -11 dBm < -11 dBm < -11 dBm
to 10 GHz < -11 dBm < -11 dBm < -11 dBm < -11 dBm
10 to GHz < -116 dBm < -115 dBm < -115 dBm < -115 dBm
to 0 GHz < -105 dBm < -10 dBm < -10 dBm < -10 dBm
0 to 0 GHz < -105 dBm < -10 dBm < -10 dBm < -10 dBm
0 to 5 GHz < -10 dBm < -10 dBm < -100 dBm < -10 dBm Option 016 degrades
5 to 50 GHz < -101 dBm < -100 dBm < -98 dBm < -100 dBm performance by dB.
50 to 60 GHz < -100 dBm < -99 dBm < -97 dBm < -99 dBm
60 to 67 GHz < -99 dBm < -97 dBm < -9 dBm < -97 dBm Option 016 degrades
67 to 70 GHz < -99 dBm < -97 dBm < -9 dBm < -97 dBm performance by dB.
1 kHz IF bandwidth
10 to 5 MHz < -50 dBm < -50 dBm < -50 dBm < -50 dBm
5 to 500 MHz , < -70 dBm < -70 dBm < -70 dBm < -70 dBm
500 MHz to GHz < -9 dBm < -9 dBm < -9 dBm < -9 dBm
to 10 GHz < -9 dBm < -9 dBm < -9 dBm < -9 dBm
10 to GHz < -96 dBm < -95 dBm < -95 dBm < -95 dBm
to 0 GHz < -85 dBm < -8 dBm < -8 dBm < -8 dBm
0 to 0 GHz < -85 dBm < -8 dBm < -8 dBm < -8 dBm
0 to 5 GHz < -8 dBm < -8 dBm < -80 dBm < -8 dBm Option 016 degrades
5 to 50 GHz < -81 dBm < -80 dBm < -78 dBm < -80 dBm performance by dB.
50 to 60 GHz < -80 dBm < -79 dBm < -77 dBm < -79 dBm
60 to 67 GHz < -79 dBm < -77 dBm < -7 dBm < -77 dBm Option 016 degrades
67 to 70 GHz < -79 dBm < -77 dBm < -7 dBm < -77 dBm performance by dB.
1. Total average (rms) noise power calculated as mean value of a linear magnitude
trace expressed in dBm.
. Noise floor may be degraded by 10 dB at particular frequencies (multiples of
5 MHz) due to spurious receiver residuals.
. Typical performance.
. Specified value is for worst-case noise floor at 5 MHz.
5. Ø Hz offset.