Alpha Technologies XM2, XM2-HV, XM2-HP - Manual (Page 64)

4.3 Smart Display Modes, continued
4.3.5 Menu Structure/Navigation
(from Active Alarms screen)
Auto-Scroll Information
To Operation Normal
(Auto-scroll Information)
OPERATION NORMAL OPERATION NORMAL
(Single-step Information)
Back to
Auto-Scroll
SETUP MENU
(Auto-scroll Information)
Back to
Auto-scroll
To
Single-step
Sample Active
Alarm
To Single-step
Help Screens
Back to Auto-Scroll
To Single-step
To Active Alarms
220GOLD
220HPL-FT
220GXL
210GXL
195GXL
195GOLD
180GXL
165GXL
115HPL-FT
85GXL
70HPL-FT
***ACTIVE ALARMS***
(Auto-scroll Information)
SELF TEST FAIL
LOW BATT VOLTS
HIGH BATT VOLTS
NO BATTERIES
BATT TEMP PROBE
LINE ISOLATION
OUTPUT FAILURE
OUTPUT OVERLOAD
OUTPUT 1 TRIPPED
OUTPUT 2 TRIPPED
CHARGER FAILURE
INPUT FAILURE
INV DISCONNECTED
INVERTER TEMP
TAP FUSE FAIL
CONFIG ERROR
N+1 IN USE
N+1 FAULT
***ACTIVE ALARMS***
(Single-step Information)
Output Overload
Single-step Information
1. OUTPUT SHORT CKT?
2. TOO MUCH LOAD
3. CHK OUTPUT CURRENT
COMMS INFO
Float V/C = 2.27 V
SETUP MENU
CODE VER = 7.01.0
DEVICE ADDRESS= 1
ALPHACELL = OTHER
FLOAT V/C=2.27
ACCEPT V/C=2.40
TEMP COMP=5mV
BATT CAPACITY=100Ah
STANDBY TIME=65M
STANDBY EVENTS=12
TOTAL RUN TIME = 365D
SELF TEST = OFF
TEST INHIBIT
TEST INTERVAL
TEST DURATION = 10M
TEST COUNTDOWN
FREQ RANGE = 3.0Hz
PIM OPTION = YES
RESET OUT 1
RESET OUT 2
OVERCURRENT 1 = 15.0A
OVERCURRENT 2 = 15.0A
RETRY DELAY = 60s
RETRY LIMIT = 20
OVER CURR TOL = 3000
N+1 VALID = NO
SET DEFAULTS = NO
SELECT LANGUAGE
COMMS INFO
(Single-step Information)
To Single-step
(Single-step Information)
CODE VER = 7.01.0
DEVICE ADDRESS= 1
ALPHACELL = OTHER
FLOAT V/C=2.27
ACCEPT V/C=2.40
TEMP COMP=5mV
BATT CAPACITY=100Ah
STANDBY TIME=65M
STANDBY EVENTS=12
TOTAL RUN TIME = 365D
SELF TEST = OFF
TEST INTERVAL
TEST INHIBIT
TEST DURATION = 10M
TEST COUNTDOWN
FREQ. RANGE = 3.0Hz
TAP SWITCH
PIM OPTION = YES
RESET OUT 1
RESET OUT 2
OVERCURRENT 1 = 15.0A
OVERCURRENT 2 = 15.0A
RETRY DELAY = 60s
RETRY LIMIT = 20
OVER CURR TOL = 3000
N+1 VALID = NO
SET DEFAULTS = NO
SELECT LANGUAGE
(Auto-scroll Information)
Back Auto-scroll
To Program Mode
To Accept New Data
To Accept
New Data
To Abort
Edit using
Back to Single-st
ep Setup Menu
LANGUAGE =
ENGLISH
SPANISH
FRENCH
PORTUGUESE
GERMAN
Output Overload
(Auto-scroll Information)
1. OUTPUT SHORT CKT?
2. TOO MUCH LOAD
3. CHK OUTPUT CURRENT
Sample Active
Alarm
Back to Auto-scroll
Help Screens
To Help screens
for selected alarm
SELF TEST FAIL
LOW BATT VOLTS
HIGH BATT VOLTS
NO BATTERIES
BATT TEMP PROBE
LINE ISOLATION
OUTPUT FAILURE
OUTPUT OVERLOAD
OUTPUT 1 TRIPPED
OUTPUT 2 TRIPPED
CHARGER FAILURE
INPUT FAILURE
INV DISCONNECTED
INVERTER TEMP
TAP FUSE FAIL
CONFIG ERROR
N+1 IN USE
N+1 FAULT
Back to
Auto-scroll
To
Single-step
To Setup Menu
Back to
COMMS Info
To
COMMS Info Back to
Operation Normal
Back to Single-st
ep Setup Menu
OPER MODE = LINE
INPUT VOLTAGE 120V
INPUT FREQUENCY 60Hz
OUTPUT VOLTAGE 89V
OUTPUT 1 CURRENT 12.2A
OUTPUT 2 CURRENT 12.0A
OUTPUT WATTS (W)
OUTPUT VA 1060
PERCENT LOAD 80%
CHARGER MODE = FLOAT
BATT VOLTAGE 40.5V
BATTERY TEMP 37°C
CHARGER CURRENT 8.2A
12 EVENTS 65 MIN
CM = 00:90:EA:00:30:54
CM192.168.1.151
CMRx PWR -6.8dBMv
CMTx PWR 41.0dBMv
DN FREQ = 300.000 MHz
UP FREQ = 15.000 MHz
SW 4.5.9.0_00.77CO-N
BATT A1=13.1 A2=14.0
BATT A3=13.5 B1=13.1
BATT B2=14.0 A2=13.5
CM = 00:90:EA:00:30:54
CM192.168.1.151
CMRx PWR -6.8dBMv
CMTx PWR 41.0dBMv
DN FREQ = 300.000 MHz
UP FREQ = 15.000 MHz
SW 4.5.9.0_00.77CO-N
BATT A1=13.1 A2=14.0
BATT A3=13.5 B1=13.1
BATT B2=14.0 A2=13.5
When an AlphaCell battery is
selected, the values for Float,
Accept, Temp Comp and
Battery Capacity are
automatically selected and not
shown in the Smart Diaplay.
Once the battery data has
been updated, the operator
will be prompted to select the
number of battery strings used
in the system.
OPER MODE = LINE
INPUT VOLTAGE 120V
OUTPUT VOLTAGE 89V
OUTPUT 1 CURRENT 12.2A
OUTPUT 2 CURRENT 12.0A
CHARGER MODE = FLOAT
BATT VOLTAGE 40.5V
BATTERY TEMP 37°C
CHARGER CURRENT 8.2A
12 EVENTS 65 MIN
*
*
* Visible when AlphaCell = Other
** Visible only on Auto-scroll screen
*** Visible when PIM option = Yes
***
***
*
* Visible only on Single-step screen
LEGEND
Description Control panel
Key
Smart Display
Symbol
UP
DOWN
ENTER
ESCAPE
*
**
*
64 017-805-B0-010 Rev. K2