Extron Electronics JMP 9600 User Guide - Manual (Page 65)

X2!
= HD-SDI enable state 0 = not enabled, 1 = enabled
X2@
= HD-SDI mode “single”, “dual_422_12”, “dual_444_10“, or “dual_444_12“ or
“dual_422_hfr“
NOTES: • The “dual_422_hfr ” high frame rate is a licensed option of the JMP 9600 2K model.
• The high frame rate supports resolutions of up to 1920x1080 and 2048x1080 at 48, 50 and 60 Hz. High frame rate uses
the dual HD-SDI connection mode per SMPTE 372M. The player must be set for 2-channel-locked mode and only content
specifically encoded for the high frame rate mode plays back correctly.
X2#
= Delay ± up to 500 milliseconds
X2$
= Volume 0 (no attenuation, full volume) through –144 (full attenuation, audio
effectively muted)
X2%
= License key 32 alphanumeric digits
X2^
= License Installed license (such as “V2HD“ or “V22K“)
X2&
= Serial port baud rate 300, 600, 1200, 1800, 2400, 4800, 9600, 19200, 38400, 57600, or
115200
X2*
= Parity “none”, “even”, or “odd”
X2(
= Data bits 7 or 8
X3)
= Stop bits 1 or 2
X3!
= Serial port mode “controlMSVPP“, “disabled“, or “passthrough”
X3@
= Ethernet port “Eth0” or “Eth1” (for LAN port 1) or “Eth2” (for LAN port 2)
X3#
= IP address, Netmask, gateway address ###.###.###.###
X3$
= DHCP on/off status “On“ or “Off”
X3%
= Hardware (MAC) address ##:##:##:##:##:##
X3^
= Digital Input port or Relay output port 1, 2, 3, or 4
X3&
= Level “+“ = high level, logic 1; “–” = low Level, logic 0
X3*
= Date In the format: MM/DD/YYYY where: MM = month: 01 (Jan) through 12 (Dec)
DD = day: 01 through 31
YYYY = year: 1970 through 2037
X3(
= Time In the format: HH:MM:SS where: HH = hour: 00 through 23
MM = minutes: 00 through 59
SS = seconds: 00 through 59
X4)
= Identifier Location or name
NOTE: If there are spaces (•) In the identifier (such as Theater 1), the entire name must be enclosed in double quotation marks in the set
command (such as “Theater 1”). Quotes are not required for a single word identifer (such as Theater).
The identifier is always in quotes in the response.
X4!
= Memory capacity or availablility In 1024-byte blocks
X4@
= Video mode / channel availability 1 (1-channel mode) or 2 (2-channel mode or 2-channel locked mode)
X4#
= Horizontal or vertical resolution Horizontal: 1280, 1920, or 2048 Vertical: 780 or 1080
X4$
= Scan type i (interlaced) or p (progressive)
X4%
= Frame rate 23.98, 24, 24, 29.97, 30, 48, 50, 59.94, or 60
X4^
= Player state “playing“, “paused”, or “stopped”
X4&
= Frame count Number of frames (total or current position)
X4*
= Percentage Current position in a playing clip expressed as a percentage
X4(
= Temperature nn.nn °C
X5)
= Voltage sensor “ps1•5vdc“ “ps2•5vdc“
“ps1•3.3vdc“ “ps2•3.3vdc“
“ps1•12vdc“ “ps2•12vdc“
“ps1•–12vdc“ “ps2•–12vdc“
NOTES: • The sensor name must be enclosed in double quotation marks as shown.
• Positive voltage sensor names must not include the positive sign (+); negative voltage sensor names must include the negative
sign (–).
X5!
= Voltage ±n.nn (3.3 vdc and 5 vdc sensors) or ±nn.nn (12 vdc sensors)
X5@
= Version
X5#
= Date
JMP 9600 Media Player • Programming Guide 59