Command and response table, For special function sis commands – Extron Electronics ISS 408 User Manual
Page 55
ISS 408 Integrated Seamless Switcher • Programming Guide
49
Command and Response Table for Special Function SIS Commands
The syntax for setting a special function is
X/*X?#
where
X/
is the value or variable (such as
35
in the first example below),
X/
is the function number (such as “set RGB delay” in the first
example below), and
#
is the execute command. To view the setting of a function, use
X?
#
where
X?
is the function number.
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
RGB delay and dissolve speed
RGB delay (Triple-Action Switching)
X2)
*3#
Dly
X2)]
Switching delay of the selected input
to the preview output. Adjustable in
0.01 second steps from
0
up to
50
= 5.0 seconds.
0
= 0.0 seconds
(default),
1
= 0.1 seconds,
2
= 0.2
seconds, and so on.
Example:
35*3#
Dly35
]
RGB delay set to 3.5 seconds.
Dissolve speed
X2)
*5#
Dur
X2)]
Adjustable in 0.1 second steps
from
1
up to
50
= 5.0 seconds.
1
= 0.1 seconds (default),
2
= 0.2 seconds,
3
= 0.3 seconds,
and so on.
Switch effect
Switching effect
X2(
*4#
Eff
X2(]
Set the switch effect,
00
= cut or
01
= dissolve, used by the Take,
%
,
command.
Scaler output settings
Output sync format
X*
*6#
Syn
X*]
00
= RGBHV (
default)
01
= RGBS
Example:
1*6#
Syn1
]
RGBHV output signal.
Output polarity
X(
*7#
Pol
X(]
X(
: Horizontal/Vertical polarity
0
= H–/V–
2
= H+/V–
1
= H–/V+
3
= H+/V+
Example:
1*7#
Pol1
]
H–/V+ output polarity.
Blue screen
Blue screen
(blue & sync output only)
X#
*8#
Blu
X#]
0
= off (normal output).
1
= on (blue video and sync output).
Example:
1*8#
Blu1
]
Blue and sync output for setup.
Edge smoothing
Edge smoothing
X#
*16#
Fil
X#]
00
= off
01
= on (
default)
Example:
1*16#
Fil01
]
Enable edge smoothing.
Enhanced mode
Enhanced mode
X#
*12#
Enh
X#]
0
= off.
1
= on.
Example:
1*12#
Enh01
]
Enable enhanced mode.
Auto Image
Set Auto Image
X#
*13#
Img
X#]
00
= off
01
= on
Example:
1*13#
Img01
]
Set Auto Image on
.
Execute Auto Image
X1*
*14#
Img
X1*]
X1*
: Auto Image input tied to output:
Prog/Prev
Prog/Prev
01
= Yes/No
03
= Yes/Yes
02
= No/Yes
X@
Reconfig
]
Output
X@
Auto Image is complete.
X@
Reconfig
]
Output
X@
Auto Image is complete.
NOTES:
•
If Auto Image adjustments are not necessary for an input, the
X@
Reconfig
]
message may not be received.
•
If both outputs are receiving the same input, both outputs are auto imaged regardless of the
X1*
received.