YSI MultiLab 4010P-1 User Manual

Operations manual

This manual is related to the following products:

MultiLab 4010-1

Table of contents

Document Outline

1 Overview
- 1.1 MultiLab 4010-1 meter
- 1.2 MultiLab 4010P-1 meter with integrated printer
- 1.3 Sensors
  - 1.3.1 IDS sensors
  - 1.3.2 Automatic sensor recognition
2 Safety
- 2.1 Safety information
- 2.2 Safe operation
3 Commissioning
- 3.1 Scope of delivery
- 3.2 Power supply
- 3.3 Initial commissioning
4 Operation
- 4.1 General operating principles
- 4.2 Switching on the meter
- 4.3 Switching off the meter
- 4.4 Login with a user name
- 4.5 Navigation
5 pH value
- 5.1 Measuring
  - 5.1.1 Measuring the pH value
  - 5.1.2 Measuring the temperature
- 5.2 pH calibration
6 ORP
- 6.1 Measuring
  - 6.1.1 Measuring the ORP
- 6.2 ORP calibration
7 Dissolved oxygen
- 7.1 Measuring
  - 7.1.1 Measuring D.O.
  - 7.1.2 Measuring the temperature
- 7.2 Calibration
8 Conductivity
- 8.1 Measuring
  - 8.1.1 Measuring the conductivity
  - 8.1.2 Measuring the temperature
- 8.2 Temperature compensation
- 8.3 Calibration
9 Settings
- 9.1 pH measurement settings
- 9.2 ORP measurement settings
  - 9.2.1 Settings for ORP measurements
- 9.3 D.O. measurement settings
- 9.4 Cond measurement settings
  - 9.4.1 Settings for IDS conductivity sensors
- 9.5 Sensor-independent settings
- 9.6 Reset
  - 9.6.1 Resetting the measurement settings
  - 9.6.2 Resetting the system settings
10 Data storage
- 10.1 Manual data storage
- 10.2 Automatic data storage at intervals
- 10.3 Measured value data storage
11 Transmitting data (USB interfaces)
- 11.1 Outputting current measurement data
- 11.2 Transmitting data (to a PC)
- 11.3 Connecting the PC / USB-B interface (USB Device)
- 11.4 Options for data transmission to a PC
- 11.5 MultiLab Importer
- 11.6 BOD Analyst Pro
12 Printer (only MultiLab 4010P-1)
- 12.1 Commissioning / switching the printer on or off
- 12.2 Operation / printing
- 12.3 Printer settings
- 12.4 Maintenance
  - 12.4.1 Changing the roll of paper (thermal paper)
- 12.5 What to do if... / printer
13 Maintenance, cleaning, disposal
- 13.1 Maintenance
  - 13.1.1 General maintenance activities
  - 13.1.2 Replacing the batteries
- 13.2 Cleaning
- 13.3 Packing
- 13.4 Disposal
14 What to do if...
- 14.1 pH
- 14.2 Dissolved oxygen
- 14.3 Conductivity
- 14.4 General information
15 Technical data
- 15.1 Measuring ranges, resolution, accuracy
- 15.2 General data
16 Firmware update
- 16.1 Firmware update for the meter MultiLab 4010-1
- 16.2 Firmware-Update for IDS Sensors
17 Glossary
18 Index
19 Appendix
- 19.1 Oxygen solubility table
- 19.2 DO% Calibration values
20 Contact Information
- 20.1 Ordering & Technical Support
- 20.2 Service Information