Garmin G1000 Quest Kodiak - Manual (Page 457)

190-00590-02 Rev. A Garmin G1000 Pilot’s Guide for the Quest Kodiak 100
SY
STEM
O
VER
VIEW
FLIGHT
INSTRUMENTS
EIS
AUDIO P
ANEL
& CNS
FLIGHT
MANA
GEMENT
HAZARD
AV
OID
ANCE
AFCS
ADDITIONAL
FEA
TURES
APPENDICES
INDEX
445
APPENDIX A
Alerts Window Message Comments
NAV1 SERVICE – NAV1 needs service.
Return unit for repair.
A failure has been detected in the NAV1 and/or NAV2 receiver. The receiver may still
be available. The G1000 system should be serviced.
NAV2 SERVICE – NAV2 needs service.
Return unit for repair.
NAV1 RMT XFR – NAV1 remote
transfer key is stuck.
The remote NAV1 and/or NAV2 transfer switch is stuck in the enabled (or “pressed”)
state. Press the transfer switch again to cycle its operation. If the problem persists,
the G1000 system should be serviced.
NAV2 RMT XFR – NAV2 remote
transfer key is stuck.
G/S1 FAIL – G/S1 is inoperative.
A failure has been detected in glideslope receiver 1 and/or receiver 2. The G1000
system should be serviced.
G/S2 FAIL – G/S2 is inoperative.
G/S1 SERVICE – G/S1 needs service.
Return unit for repair.
A failure has been detected in glideslope receiver 1 and/or receiver 2. The receiver
may still be available. The G1000 system should be serviced when possible.
G/S2 SERVICE – G/S2 needs service.
Return unit for repair.
GEA 71 Message Advisories
Alerts Window Message Comments
GEA1 CONFIG – GEA1 config error.
Config service req’d. The GEA1 configuration settings do not match those of backup configuration memory.
The G1000 system should be serviced.
GEA2 CONFIG – GEA2 config error.
Config service req’d. The GEA2 configuration settings do not match those of backup configuration memory.
The G1000 system should be serviced.
MANIFEST – GEA1 software
mismatch, communication halted. The #1 GEA 71 has incorrect software installed. The G1000 system should be
serviced.
MANIFEST – GEA2 software
mismatch, communication halted. The #2 GEA 71 has incorrect software installed. The G1000 system should be
serviced.
GTX 33 Message Advisories
Alerts Window Message Comments
XPDR1 CONFIG – XPDR1 config error.
Config service req’d. The transponder configuration settings do not match those of backup configuration
memory. The G1000 system should be serviced.
XPDR2 CONFIG – XPDR2 config error.
Config service req’d. The transponder configuration settings do not match those of backup configuration
memory. The G1000 system should be serviced.
MANIFEST – GTX1 software
mismatch, communication halted. The transponder has incorrect software installed. The G1000 system should be
serviced.
MANIFEST – GTX2 software
mismatch, communication halted. The transponder has incorrect software installed. The G1000 system should be
serviced.
XPDR1 SRVC – XPDR1 needs service.
Return unit for repair.
The #1 transponder should be serviced when possible.
XPDR2 SRVC – XPDR2 needs service.
Return unit for repair.
The #2 transponder should be serviced when possible.
XPDR1 FAIL – XPDR1 is inoperative. There is no communication with the #1 transponder.
XPDR2 FAIL – XPDR2 is inoperative. There is no communication with the #2 transponder.