Texas Instruments TMS320DM357 User Manual
Page 66
USB Controller Host and Peripheral Modes Operation
www.ti.com
The software enables packet reception on a given channel by writing the address of the first buffer
descriptor in the queue (nonzero value) to the channel’s head descriptor pointer (RCCPIDMASTATEW1)
in the channel’s Rx DMA state. When packet reception begins on a given channel, the DMA controller fills
each Rx buffer with data in order starting with the first buffer and proceeding through the Rx queue. If the
Buffer Offset in the Rx DMA State is nonzero, then the controller will begin writing data after the offset
number of bytes in the SOP buffer. The DMA controller performs the following operations at the end of
each packet reception:
•
Overwrite the buffer length in the packet’s EOP buffer descriptor with the number of bytes actually
received in the packet’s last buffer. The software initialized value is the buffer size. The overwritten
value will be less than or equal to the software initialized value.
•
Set the EOP bit in the packet’s EOP buffer descriptor.
•
Set the EOQ bit in the packet’s EOP buffer descriptor if the current packet is the last packet in the
queue.
•
Overwrite the packet’s SOP buffer descriptor Buffer Offset with the Rx DMA state value (the software
initialized the buffer descriptor Buffer Offset value to zero). All non SOP buffer descriptors must have a
zero Buffer Offset initialized by the host.
•
Overwrite the packet’s SOP buffer descriptor buffer length with the number of valid data bytes in the
buffer. If the buffer is filled up, the buffer length will be the buffer size minus buffer offset.
•
Set the SOP bit in the packet’s SOP buffer descriptor.
•
Write the SOP buffer descriptor Packet Length field.
•
Clear the Ownership bit in the packet’s SOP buffer descriptor.
•
Issue an Rx DMA interrupt to the host processor by writing the address of the packet’s last buffer
descriptor to the queue’s Rx DMA State Completion Pointer (RCPPICOMPPTR register).
On interrupt the software processes the Rx buffer queue detecting received packets by the status of
the Ownership bit in each packet’s SOP buffer descriptor. If the Ownership bit is cleared then the
packet has been completely received and is available to be processed by the software. The software
may continue Rx queue processing until the end of the queue or until a buffer descriptor is read that
contains a set Ownership bit indicating that the next packet’s reception is not complete. The software
determines that the Rx queue is empty when the last packet in the queue has a cleared Ownership bit
in the SOP buffer descriptor, a set End of Queue bit in the EOP buffer descriptor, and the Next
Descriptor Pointer in the EOP buffer descriptor is zero.
The software acknowledges an interrupt by writing the address of the last buffer descriptor to the
queue’s associated Rx Completion Pointer (RCPPICOMPPTR register).
If the software written buffer address value in RCCPICOMPPTR register is different from the buffer
address written by the DMA controller after Rx completion, then the interrupt for the Rx Channel
remains asserted. If the software written buffer address value matches with the buffer address written
by the DMA controller, the Rx Channel interrupt gets deasserted.
A misqueued buffer may occur when the software adds buffers to a queue as the DMA controller
finishes the reception of the previous last packet in the queue. The misqueued buffer is detected by the
software when queue processing detects a cleared Ownership bit in the SOP buffer descriptor, a set
End of Queue bit in the EOP buffer descriptor, and a nonzero Next Descriptor Pointer in the EOP
buffer descriptor. A misqueued buffer means that the DMA controller read the last EOP buffer
descriptor before the software added buffer descriptor(s) to the queue, so the DMA controller
determined queue empty just before the software added more buffer descriptor(s). Receive overrun
condition may occur in the misqueued buffer case. If a new packet reception is begun during the time
that the DMA controller has determined the end of queue condition, then the received packet will
overrun (start of packet overrun). If the misqueued buffer occurs during the middle of a packet
reception then middle of packet overrun may occur. If the misqueued buffer occurs after the last packet
has completed, and is corrected before the next packet reception begins, then overrun will not occur.
The software acts on the misqueued buffer condition by writing the added buffer descriptor address to
the appropriate Rx DMA State Head Descriptor Pointer in RCPPIDMASTATEW1 register.
Universal Serial Bus (USB) Controller
66
SPRUGH3 – November 2008