Roland VC-2 - Manual (Page 55)

55
Effects List
29: OD/DS → Delay
(Overdrive/Distortion → Delay)
This effect connects either Overdrive or Distortion and Delay
in series.
30: Cho/Flg → Delay
(Chorus/Flanger → Delay)
This effect connects either Chorus or Flanger and Delay in
series.
Parameter Value Description
Drive Mode OD, DS Selects whether to use overdrive
(OD) or distortion (DS).
Drive 0–127 Degree of distortion
Amp Sim Sw OFF, ON Turns the amp simulator on/off.
Amp Type SMALL,
BUILT-IN,
2-STACK,
3-STACK Type of guitar amp
SMALL: small amp
BUILT-IN: single-unit type amp
2-STACK: large double stack amp
3-STACK: large triple stack amp
Distortion
(DS) Level 0–127 Volume of the overdrive or distor-
tion sound.
Delay Time 0–1300 ms,
note Adjusts the delay time from the di-
rect sound until the delay sound is
heard.
Delay Feed-
back -98– +98 % Adjusts the proportion of the delay
sound that is fed back into the ef-
fect. Negative (-) settings will in-
vert the phase.
Low Damp
Freq 50–4000 Hz Adjusts the frequency below
which sound fed back to the effect
will be cut.
The Low Damp function damps
the low frequency band of the de-
lay sound quicker than other
bands, which makes for a clearer
delay effect.
Low Damp
Gain -36–0 dB Degree of Low Damp
Hi Damp
Freq 2000–20000 Hz Adjusts the frequency above
which sound fed back to the effect
will be cut.
High Damp, by attenuating the
higher frequencies first, makes the
delay sound more natural.
Hi Damp
Gain -36–0 dB Degree of High Damp
Delay Level 0–127 Volume of the delay sound.
Ps Low Freq 50–4000 Hz Frequency of the low range
Ps Low Gain -15– +15 dB Gain of the low range
Ps Hi Freq 2000–20000 Hz Frequency of the high range
Ps Hi Gain -15– +15 dB Gain of the high range
Parameter Value Description
Mod Mode CHORUS,
FLANGER Selects whether to use chorus or
flanger.
Mod Rate 0.05–10.0 Hz,
note Adjusts the speed of modulation
for the chorus or flanger.
Mod Depth 0–127 Adjusts the depth of modulation
for the chorus or flanger.
Mod Phase 0–180 deg Sets how the chorus or flanger
sound is spread.
Mod Pre De-
lay 0–50.0 ms Adjusts the delay time from the di-
rect sound until the chorus or
flanger sound is heard.
Mod Feed-
back -98– +98% Adjusts the proportion of the effect
sound that is fed back into the ef-
fect. Negative (-) settings will in-
vert the phase.
Xover Low-
Freq 50–4000 Hz Attenuates the effect in the range
below the specified frequency.
Xover Low
Gain -36–0 dB Specifies how greatly the low range
will be attenuated.
Xover Hi-
Freq 2000–20000 Hz Attenuates the effect in the range
above the specified frequency.
Xover Hi
Gain -36–0 dB Specifies how greatly the high
range will be attenuated.
Mod Level 0–127 Volume of the chorus or flanger
sound.
Delay Time 0–1300 ms,
note Adjusts the delay time from the di-
rect sound until the delay sound is
heard.
Delay Feed-
back -98– +98% Adjusts the proportion of the delay
sound that is fed back into the ef-
fect. Negative (-) settings will in-
vert the phase.
Low Damp
Freq 50–4000 Hz Adjusts the frequency below which
sound fed back to the effect will be
cut.
The Low Damp function damps the
low frequency band of the delay
sound quicker than other bands,
which makes for a clearer delay ef-
fect.
Low Damp
Gain -36–0 dB Degree of Low Damp
Hi Damp
Freq 2000–20000 Hz Adjusts the frequency above which
sound fed back to the effect will be
cut.
High Damp, by attenuating the
higher frequencies first, makes the
delay sound more natural.
Hi Damp
Gain -36–0 dB Degree of High Damp
Delay Level 0–127 Volume of the delay sound.
Ps Low Freq 50–4000 Hz Frequency of the low range
Ps Low Gain -15– +15 dB Gain of the low range
Ps Hi Freq 2000–20000 Hz Frequency of the high range
Ps Hi Gain -15– +15 dB Gain of the high range
Parameter Value Description
vc2_for_XT_e1 55 ページ ２００５年３月８日 火曜日 午後４時５２分