Kenwood XV-2020 - Manual (Page 80)

80
Using the XV-2020 Effects
Multi-Effects Parameter
PATCH/RHYTHM MFX, PERFORM MFX (Multi-Effects Settings)
PATCH/PERFORMANCE CHORUS (Chorus Settings)
PATCH/PERFORMANCE REVERB (Reverb Settings)
Parameter Value Description
TYPE
(Multi-Effects Type) 00 (THROUGH) –40 Use this parameter to select from among the 40 available Multi-effects.
* For details on Multi-effects parameters, refer to “
Multi-Effects Parameters
(p. 82).”
SEND LEVEL DRY
(Multi-Effects Dry Send Level) 0–127 Adjusts the volume of the sound that has passed through the Multi-effects.
SEND LEVEL CHO
(Multi-Effects Chorus Send Level) 0–127 Adjusts the amount of Chorus for the sound that passes through Multi-ef-
fects. If you don’t want to add the Chorus effect, set it to 0.
SEND LEVEL REV
(Multi-Effects Reverb Send Level) 0–127 Adjusts the amount of Reverb for the sound that passes through Multi-ef-
fects. If you don’t want to add the Reverb effect, set it to 0.
CONTROL SOURCE 1–4
(Multi-Effects Control Source) OFF, CC01–31,
CC33–95, BEND,
AFTER, SYS1–4 Selects the Control Source to be used for changing the Multi-effects param-
eters.
DESTINATION 1–4
(Multi-Effects Control Destination
1–4) Refer to “ Multi-Effects
Parameters (p. 82).”
Selects the Multi-effects parameter to be controlled using Ctrl Src 1–4. The
parameters that can be selected depend on which type of Multi-effects is
set to MFX Type.
SENS 1–4
(Multi-Effects Control Sensitivity
1–4) -63–+63 If you wish to modify the selected parameter in a positive (+) direction—
i.e., a higher value, toward the right, or faster, etc.—from its current set-
ting, select a positive (+) value. If you wish to modify the selected param-
eter in a negative (-) direction—i.e., a lower value, toward the left, or
slower, etc.—from its current setting, select a negative (-) value. Higher
numbers produce a greater amount of change.
SOURCE MFX
(Multi-Effects Source) PERFORM, PART 1–16 Selects the Multi-effects parameter settings that will be used by the Perfor-
mance. If you wish to use the Performance settings, select PERFORM. If
you wish to use the settings of the Patch/Rhythm Set assigned to one of
the Parts, select the Part number. (When using the XV Editor, you can
make this setting in the PERFORM PART ALL screen. p. 71)
Parameter Value Description
TYPE
(Chorus Type) OFF, CHORUS This determines whether or not chorus is used.
LEVEL
(Chorus Level) 0–127 Adjusts the volume of the sound that has passed through chorus.
OUTPUT SELECT
(Chorus Output Select) MAIN, REV,
MAIN+REV Specifies how the sound routed through Chorus will be output.
MAIN: Output to the OUTPUT jacks in stereo.
REV: Output to Reverb in mono.
MAIN+REV: Output to the OUTPUT jacks in stereo, and to Reverb in mono.
* Used in Performance mode.
CHORUS
(Chorus Source) PERFORM,
PART 1–16 Selects the Chorus parameter settings that will be used by the Performance. If you wish to use
the Performance settings, select PERFORM. If you wish to use the settings of the Patch/
Rhythm Set assigned to one of the Parts, select the Part number.
* Used in Performance mode.
Parameter Value Description
TYPE
(Reverb Type) OFF, REVERB This determines whether or not reverb is used.
LEVEL
(Reverb Level) 0–127 Adjusts the volume of the sound that has passed through Reverb.
REVERB
(Reverb Source) PERFORM,
PART 1–16 Selects the Reverb parameter settings that will be used by the Performance. If you wish to use
the Performance settings, select PERFORM. If you wish to use the settings of the Patch/
Rhythm Set assigned to one of the Parts, select the Part number.
* Used in Performance mode.