JVC UX-J99DVD - Manual (Page 56)

53
English
Recording Discs onto an MD and a Tape
—Disc Synchronized Recording
With this recording method, you can start and stop disc play, MD
and tape recordings at the same time.
1
Load discs into the 5-DVD changer.
• If the current playing source is not “DVD,” press
DVD 3 (or #¥8 DVD on the unit), then 7 before going to the
next step.
• You can make a program (see page 21) or select Random Play
(see page 22) if you want. = Go to step 3 .
On the remote control ONLY:
2
Press DISC UP or DISC DOWN to select the disc
you want to record, then
7 before going to the
next step.
3
Insert a recordable MD into the MD loading slot
and put a recordable cassette into the cassette
loading slot.
• When you select a track by pressing ¢ or 4 before the
disc playback, recording starts from the selected track (except
when Program Play is selected).
For the MD:
Set the MD recording length mode, “LP:”-prefix addition mode,
and group recording mode (see “Setting MD Recording Modes”
on page 46).
• Set the MD recording speed to “x1” by pressing REC SPEED
button. You cannot select “x5” to record on an MD and a
TAPE at the same time.
For the cassette:
Press REV.MODE to select Reverse Mode as necessary.
4
Press MD&TAPE REC.
Disc play and recording start.
• When you press MD&TAPE REC before or after play,
“DSC =MD&TAPE” appears on the display.
• When you press MD&TAPE REC during play,
“1TR =MD&TAPE” appears on the display.
The REC (MD recording) and REC (tape recording) indicators
start flashing on the display.
When disc player stops, MD recorder and the cassette deck stop
automatically.
To stop recording, press 7.
“WRITING” flashes on the display for a while.
To eject the MD or tape, press 7 to stop the recording, then press
the corresponding eject button.
To record a single track during play or pause
On the remote control ONLY:
While playing back or pausing a track you
want to record, press MD&TAPE REC.
The playback of the track is stopped, and the same track starts
playing from the beginning again. This time, the MD recorder and
cassette deck start recording the track.
• After the track is recorded, both playback and recording stop
automatically.
To record from the desired track
• Select the track before playback, then press TAPE&MD REC.
• When you made a program, you can select one of the programed tracks
during playback.
To change the information shown on the display
On the remote control ONLY:
Press DISP/CHARA.
* If the loaded MD does not contain any group or more than 99 groups,
“G – –” will appear on the display.
When recording on an MD and a tape at the same time
A 4-second blank before each track is not made on the tape.
Current disc tray number
The track number on the disc
currently being recorded
MD and tape
recording indicators Elapsed
playing time
C D TAPE
REC REC 1 2 3 4 5
MD
x 1
SP
C D
x 1
TAPE
REC REC 1 2 3 4 5
MD
GROUP
LP 2
C D
x 1
TAPE
REC REC 1 2 3 4 5
MD
GROUP
LP 2
C D
x 1
TAPE
REC REC 1 2 3 4 5
MD
GROUP
LP 2
C D
x 1
TAPE
REC REC 1 2 3 4 5
MD
GROUP
LP 2
Remaining recording time
Current MD track number Current group number*
Elapsed playing time
Recording on a Tape
(Continued)
EN45-53_UX-J99DVD[UB]5.p65 03.12.12, 11:04 PM 53