HandHeld Entertainment Document Reader 4800dr - Manual (Page 46)

5 - 2 4800dr Barcode Guide
• Save from the Programming Chart inside the back cover of this manual
This exits, saving any Data Format changes.
• Discard from the Programming Chart inside the back cover of this manual
This exits without saving any Data Format changes.
Data Format Editor Commands
Send Commands
F1 Send all characters followed by “xx” key or function code, starting from current cursor position. Syntax = F1xx (xx stands
for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) , page A-3.)
F2 Send “nn” characters followed by “xx” key or function code, starting from current cursor position. Syntax = F2nnxx (nn
stands for the numeric value (00-99) for the number of characters and xx stands for the hex value for an ASCII code. See
ASCII Conversion Chart (Code Page 1252) , page A-3.)
F3 Send up to but not including “ss” character (Search and Send) starting from current cursor position, leaving cursor pointing
to “ss” character followed by “xx” key or function code. Syntax = F3ssxx (ss and xx both stand for the hex values for ASCII
codes, see ASCII Conversion Chart (Code Page 1252) , page A-3.)
F4 Send “xx” character “nn” times (Insert) leaving cursor in current cursor position. Syntax = F4xxnn (xx stands for the hex
value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) , page A-3, and nn is the numeric value (00-99) for
the number of times it should be sent.)
E9 Send all but the last “nn” characters, starting from the current cursor position. Syntax = E9nn (nn is the numeric value
(00-99) for the number of characters that will not be sent at the end of the message.)
Move Commands
F5 Move the cursor ahead “nn” characters from current cursor position.
Syntax = F5nn (nn stands for the numeric value (00-99) for the number of characters the cursor should be moved ahead.)
F6 Move the cursor back “nn” characters from current cursor position.
Syntax = F6nn (nn stands for the numeric value (00-99) for the number of characters the cursor should be moved back.)
F7 Move the cursor to the beginning of the data string. Syntax = F7.
EA Move the cursor to the end of the data string. Syntax = EA
Search Commands
F8 Search ahead for “xx” character from current cursor position, leaving cursor pointing to “xx” character. Syntax = F8xx (xx
stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) , page A-3.)
F9 Search back for “xx” character from current cursor position, leaving cursor pointing to “xx” character. Syntax = F9xx (xx
stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) , page A-3.)
E6 Search ahead for the first non “xx” character from the current cursor position, leaving cursor pointing to non “xx” character.
Syntax = E6xx (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) , page A-3.
E7 Search back for the first non “xx” character from the current cursor position, leaving cursor pointing to non “xx” character.
Syntax = E7xx (xx stands for the hex value for an ASCII code, see ASCII Conversion Chart (Code Page 1252) , page A-3.)
Miscellaneous Commands
FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is advanced
by other commands. When the FC command is encountered, the suppress function is terminated. The cursor is not moved
by the FB command. Syntax = FBnnxxyy . .zz where nn is a count of the number of suppressed characters in the list and
xxyy .. zz is the list of characters to be suppressed. (xx stands for the hex value for an ASCII code, see ASCII Conversion
Chart (Code Page 1252) , page A-3.)
FC Disables suppress filter and clear all suppressed characters. Syntax = FC.
E4 Replaces up to 15 characters in the data string with user specified characters. Replacement continues until the E5 com-
mand is encountered. Syntax = E4nnxx
1
xx
2
yy
1
yy
2
...zz
1
zz
2
where nn is the total count of both characters to be replaced
plus replacement characters; xx
1
defines characters to be replaced and xx
2
defines replacement characters, continuing
through zz
1
and zz
2
.
E5 Terminates character replacement. Syntax = E5.
FE Compare character in current cursor position to the character “xx.” If characters are equal, increment cursor. If characters
are not equal, no format match. Syntax = FExx (xx stands for the hex value for an ASCII code, see ASCII Conversion
Chart (Code Page 1252) , page A-3.)
EC Check to make sure there is an ASCII number at the current cursor position. If character is not numeric, format is aborted.
Syntax = EC .
ED Check to make sure there is a non-numeric ASCII character at the current cursor position. If character is numeric, format is
aborted. Syntax = ED.