Roland V-160HD SDI/HDMI Streaming Video Switcher - Manual (Page 5)

5
Panel Descriptions
5 DSK 1, 2
This uses DSK layer 1 or 2 to composite video using a downstream
keyer (p. 30).
[LEVEL] knob
Adjusts the degree of extraction (transparency) for the key.
[GAIN] knob
Adjusts the degree of edge blur (semi-transmissive region) for the
key.
[SOURCE] button
When this is on (lit), you can select the DSK video source using the
7 PinP & KEY SOURCE [1]–[10] buttons.
[PVW] button
Turns the preview output of the DSK compositing result on/off.
[PGM] button
This switches DSK composition on or off.
6 [MODE] button
7 Switches the functioning of the AUX / MEMORY / MACRO [1]–
[10] buttons. An indicator located at the left of the [MODE] button
is lit to indicate the current function.
7 AUX / MEMORY / MACRO / PinP & KEY SOURCE /
DSK SOURCE / CAMERA PRESET [1]–[10] buttons
The functions of these buttons change as shown in the table
below.
When button is lit Functions of buttons [1]–[10]
[MODE]
AUX
Select the video that is sent to the AUX bus.
MEMORY
Recalls the preset memory (the video/audio
and other data that is saved). Long-press a
button to save the current settings in a preset
memory.
MACRO
Executes a macro (a series of recorded
operations).
PinP & KEY 1–4
[SOURCE]
PinP & KEY SOURCE
Select the video source for the inset screen (p.
28).
DSK 1, 2 [SOURCE]
DSK SOURCE
Selects the DSK video source (p. 30).
USER [4]
(CAMERA CONTROL)
CAMERA PRESET
Recalls the registered preset (camera position,
focus settings, etc.) from the connected camera.
8 [PGM/A-CENTER] [PST/B-CENTER] knobs
Adjust the split compositing settings (p. 27).
Knob Explanation
[PGM/A-CENTER]
Adjusts the horizontal/vertical position of the
video that’s shown in the left or upper area.
Turn while pressing:
Adjusts the position of the boundary.
[PST/B-CENTER]
Adjusts the horizontal/vertical position of the
video that’s shown in the right or lower area.
Turn while pressing:
Adjusts the position of the boundary.
9 [SPLIT 1] [SPLIT 2] buttons
Turns on/off video compositing using split (p. 27).
10 PGM/A cross-point [1]–[10] buttons
Selects the video to input to bus PGM/A. The selected button
lights up.
11 PST/B cross-point [1]–[10] buttons
Selects the video to input to bus PST/B. The selected button lights
up.
12 [INPUT ASSIGN] button
Press a cross-point button while holding down the [INPUT ASSIGN]
button to change the video source for the buttons you pressed.
The video source changes in the following order each time you
press the button.
¹ [INPUT ASSIGN] + PGM/A cross-point buttons
STILL 16
У
1
У
SDI 8
У
1
У
HDMI 8
Ó
1
¹ [INPUT ASSIGN] + PST/B cross-point buttons
HDMI 1
У
8
У
SDI 1
У
8
У
STILL 1
Ó
16
13 [TRANSITION] button
Selects the video transition effects (MIX, WIPE).
The MIX or WIPE indicator lights to show that it is selected.
14 [CUT] [AUTO] button
Automatically switch between the videos being input to bus
PGM/A and PST/B, and send them to the final output.
Button Explanation
[CUT] The picture switches instantly.
[AUTO]
A transition effect is applied and the video is switched
automatically.
15 (Bluetooth®) indicator
Shows the Bluetooth connection status.
Lit Connected Rapid blinking Now pairing
Unlit Bluetooth off Blinking Waiting for connection
You can input audio from an audio device that uses Bluetooth, or
use dedicated app on your computer or iPad to remotely control
the V-160HD.
16 Video fader
Manually switch between the videos being input to bus PGM/A
and PST/B, and send them to the final output.
Transition indicator
The indicators light up to show the video fader position.
When the video fader is pushed all the way down, only the
topmost or bottommost transition indicator lights.
17 Monitor
Shows the input/output video, a loaded still image, or a menu.
* The same video as that shown on the monitor of this unit is output
from the HDMI OUT 3 connector.