Yaskawa AC Drive Z1000 - Manual (Page 12)

i.1 Preface
Yaskawa manufactures products used as components in a wide variety of industrial systems and equipment. The selection and
application of Yaskawa products remain the responsibility of the equipment manufacturer or end user. Yaskawa accepts no
responsibility for the way its products are incorporated into the final system design. Under no circumstances should any
Yaskawa product be incorporated into any product or design as the exclusive or sole safety control. Without exception, all
controls should be designed to detect faults dynamically and fail safely under all circumstances. All systems or equipment
designed to incorporate a product manufactured by Yaskawa must be supplied to the end user with appropriate warnings and
instructions as to the safe use and operation of that part. Any warnings provided by Yaskawa must be promptly provided to
the end user. Yaskawa offers an express warranty only as to the quality of its products in conforming to standards and
specifications published in the Yaskawa manual. NO OTHER WARRANTY, EXPRESS OR IMPLIED, IS OFFERED.
Yaskawa assumes no liability for any personal injury, property damage, losses, or claims arising from misapplication of its
products.
This manual is designed to ensure correct and suitable application of Z1000-series drives. Read this manual before attempting
to install, operate, maintain, or inspect a drive and keep it in a safe, convenient location for future reference. Be sure you
understand all precautions and safety information before attempting application.
u Applicable Documentation
The following manuals are available for Z1000-series drives:
危 険
据え付け、運転の前には必ず取扱説明書を読むこと。
通電中および電源遮断後 5 分以内はフロントカバー を外さない事。 400V 級インバータの場合は、電源の中性点が接地 されていることを確認すること 。 ( 対応） 保守・点検、配線を行う場合は、出力側開閉器を
遮断後 5 分待って実施してください。
けが．感電のおそれがあります。
高温注意 インバータ上部、両側面は高温になります。
触らないでください。
● ● ●
●
AVERTISSMENT NPJT31470-1
Lire le manuel avant l'installation. Attendre 5 minutes après la coupure de l'alimentation, pour permettre la décharge des condensateurs. Pour répondre aux exigences , s assurer que le neutre soit relié à la terre, pour la série 400V. Après avoir déconnécte la protection entre le driver et le moteur, veuillez patienter 5 minutes avain d’effectuer une opération de montage ou de câblage du variateur.
Risque de décharge électrique.
Surfaces Chaudes Dessus et cotés du boitier Peuvent devenir chaud. Ne Pas toucher.
WARNING
Read manual before installing. Wait 5 minutes for capacitor discharge after disconnecting power supply. To conform to requirements, make sure to ground the supply neutral for 400V class. After opening the manual switch between the drive and motor, please wait 5 minutes before inspecting, performing maintenance or wiring the drive.
Risk of electric shock.
Hot surfaces Top and Side surfaces may become hot. Do not touch.
● ● ●
●
●
● ●
● ●
●
● ● ● ● ●
F2 F1
ESC M M
AUTO OFF
ENTER RESET
ALM DIGITAL OPERATOR JVOP-183
HAND
Z1000-Series AC Drive User Manual (TOEPC71061645)
Read this manual first. This manual is packaged together with the product and contains basic information required to install
and wire the drive. It also gives detailed information on fault diagnostics, parameter settings, and BACnet specifications.
The purpose of this manual is to prepare the drive for a trial run with an application and for basic operation. This manual
is available for download on our documentation website, www.yaskawa.com.
Z1000-Series AC Drive Programming Manual (SIEPC71061645)
This manual provides detailed information on parameter settings, drive functions, maintenance, and MEMOBUS/Modbus
specifications. Use this manual to expand drive functionality. This manual is available for download on our documentation
website, www.yaskawa.com.
u Symbols
Note: Indicates a supplement or precaution that does not cause drive damage.
TERMS TERMS
Indicates a term or definition used in this manual.
u Terms and Abbreviations
TERMS TERMS
• Drive: Yaskawa Z1000-Series Drive
• H: Hexadecimal Number Format
• IGBT: Insulated Gate Bipolar Transistor
• kbps: Kilobits per Second
• MAC: Media Access Control
• r/min: Revolutions per Minute
• V/f: V/f Control
• OLV/PM: Open Loop Vector Control for PM
• PM motor: Permanent Magnet Synchronous motor (an abbreviation for IPM motor or SPM motor)
• IPM motor: Interior Permanent Magnet Motor (e.g., Yaskawa SSR1 Series and SST4 Series motors)
• SPM motor: Surface mounted Permanent Magnet Motor (e.g., Yaskawa SMRA Series motors)
u Trademarks
• APOGEE® FLN is a registered trademark of Siemens Building Technologies, Inc.
• APOGEE® Anywhere™ is a trademark of Siemens Building Technologies, Inc.
• BACnet is a trademark of the American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ASHRAE).
• GPD is a trademark of Yaskawa, Inc.
i.1 Preface
12 YASKAWA ELECTRIC TOEP C710616 45E YASKAWA AC Drive – Z1000 User Manual