Reznor HRPD (Outdoor Duct Furnaces) Unit Installation Manual - Manual (Page 6)

Form I-RP/HRPD, P/N 132210 R14, Page 6
A
D - Mounting
3-9/32” (83mm)
4-1/16”
103mm
4-1/16”
103mm 2-1/2”
64mm
Alernate
Thermostat
Connection
Alternate
Electric
Connection
1/4” (6mm) dia.
Condensate
Drain (4)
per side
1/2”
13mm
Approx Location of Gas Connection
(for size see Techical Table)
15/16”
24mm
1-1/8”
29mm
1-1/8”
29mm
16-1/4”
413mm
Thermostat
Connection
Electric
Connection
C
3/4”
19mm
3/4”
19mm
G
10-9/16”
268mm
18”
457mm
8-15/32”
215mm
38-17/32”
979mm
3/4”
19mm
3/4”
19mm
LEFT SIDE VIEW
FRONT VIEW
REAR VIEW
TOP VIEW
B
50-1/4”
1280mm
18-3/32”
460mm
AIR
FLOW
1/2”
13mm
52” (1321mm)
51” (1295mm) - Mounting
15/16”
24mm
AIR
FLOW
4.0 Dimensions and Clearances (cont'd)
4.1 Dimensions (cont'd)
FIGURE 2B - Dimensions, Model Series HRPD
Dimensions (inches) Dimensions (mm)
Size A B C D E Size A B C D E
250 30-15/16 28-1/2 15-1/4 20-5/16 3-3/32 250 786 724 387 516 79
300 36-7/16 34 20-3/4 25-13/16 1-21/32 300 926 864 527 656 42
350 36-7/16 34 20-3/4 25-13/16 1-21/32 350 926 864 527 656 42
400 41-15/16 39-1/2 26-1/4 31-5/16 1-21/32 400 1065 1003 667 795 42
500 50-3/16 47-3/4 34-1/2 39-9/16 1-21/32 500 1275 1213 876 1005 42
600 50-3/16 47-3/4 34-1/2 39-9/16 1-21/32 600 1275 1213 876 1005 42
700 55-11/16 53-1/4 40 45-1/16 1-21/32 700 1414 1353 1016 1145 42
800 61-3/16 58-3/4 45-1/2 50-9/16 1-21/32 800 1554 1492 1156 1284 42
4.2 Clearances Clearance to combustibles is defined as the minimum distance from the heater to a
surface or object that is necessary to ensure that a surface temperature of 90°F above
the surrounding ambient temperature is not exceeded.
Clearance is also required to sides of furnace for service.
Required C learances
Models Top
Sides* Bottom
Control
Opposite
Controls
To
Combustibles
To Non-
Combustibles
RP, HRPD
Series
inches 36 Width of furnace plus 6 6 0 0
mm 914 Width of furnace plus 152 152 0 0
* Provide clearance as shown for safety, for combustion air, and for service.
5.0 Mounting
Before installing the furnace, check the supporting structure to be used to verify that it
has sufficient load-carrying capacity to support the weight of the unit. Lifting holes are
provided at each of the four corners of the mounting support rails. Use spreader bars
when lifting to prevent chains or cables from damaging the cabinet. Furnaces must be
level.
Weights
Model Approximate Net Wt (lbs) Approximate Net Wt - kg
RP by
Size
125 150 175 200 225 250 300 350 400 125 150 175 200 225 250 300 350 400
201 217 217 247 247 295 295 333 361
91 98 98 112 112 134 134 151 164
HRPD by
Size
250 300 350 400 500 600 700 800 250 300 350 400 500 600 700 800
402 434 434 494 590 590 666 722 182 196 196 224 268 268 302 328
Mounting Models RP, HRPD - These furnaces may be placed directly on a slab or
roof where support is adequate. Support rails provide required clearance from combus-
tibles. See mounting requirements in FIGURE 3.