Interlogix NX-8E Installation Manual - Manual (Page 58)

Chapter 2: Reporting codes
54 NX-8E Control Panel Installation Manual
Location 194
Zones 145 to 152 zone
types Location 194 has eight segments of numerical data. Use this location
to program the zone type for zones 145 to 152. Use segment 1 for
zone 145, segment 2 for zone 146, etc. The segment defaults are 6,
6, 6, 6, 6, 6, 6, 6.
Location 195
Zones 145 to 152
partition Location 195 has eight segments of feature selection data. Use this
location to select the partitions (1 to 8) that zones 145 to 152 reside in.
Each segment corresponds to a zone (segment 1 to zone 145,
segment 2 to zone 146, etc.). In each segment, enter 1 for partition 1
through 8 for partition 8.
Location 196
Zones 153 to 160 zone
types Location 196 has eight segments of numerical data. Use this location
to program the zone type for zones 153 to 160. Use segment 1 for
zone 153, segment 2 for zone 154, etc. The segment defaults are 6,
6, 6, 6, 6, 6, 6, 6.
Location 197
Zones 153 to 160
partition Location 197 has eight segments of feature selection data. Use this
location to select the partitions (1 to 8) that zones 153 to 160 reside in.
Each segment corresponds to a zone (segment 1 to zone 153,
segment 2 to zone 154, etc.). In each segment, enter 1 for partition 1
through 8 for partition 8.
Location 198
Zones 161 to 168 zone
types Location 198 has eight segments of numerical data. Use this location
to program the zone type for zones 161 to 168. Use segment 1 for
zone 161, segment 2 for zone 162, etc. The segment defaults are 6,
6, 6, 6, 6, 6, 6, 6.
Location 199
Zones 161 to 168
partition Location 199 has eight segments of feature selection data. Use this
location to select the partitions (1 to 8) that zones 161 to 168 reside in.
Each segment corresponds to a zone (segment 1 to zone 161,
segment 2 to zone 162, etc.). In each segment, enter 1 for partition 1
through 8 for partition 8.
Location 200
Zones 169 to 176 zone
types Location 200 has eight segments of numerical data. Use this location
to program the zone type for zones 169 to 176. Use segment 1 for
zone 169, segment 2 for zone 170, etc. The segment defaults are 6,
6, 6, 6, 6, 6, 6, 6.
Location 201
Zones 169 to 176
partition Location 201 has eight segments of feature selection data. Use this
location to select the partitions (1 to 8) that zones 169 to 176 reside in.
Each segment corresponds to a zone (segment 1 to zone 169,
segment 2 to zone 176, etc.). In each segment, enter 1 for partition 1
through 8 for partition 8.
Location 202
Zones 177 to 184 zone
types Location 202 has eight segments of numerical data. Use this location
to program the zone type for zones 177 to 184. Use segment 1 for
zone 177, segment 2 for zone 177, etc. The segment defaults are 6,
6, 6, 6, 6, 6, 6, 6.
Location 203
Zones 177 to 184
partition Location 203 has eight segments of feature selection data. Use this
location to select the partitions (1 to 8) that zones 177 to 184 reside in.
Each segment corresponds to a zone (segment 1 to zone 177,
segment 2 to zone 178, etc.). In each segment, enter 1 for partition 1
through 8 for partition 8.