Interlogix NX-8E Installation Manual - Manual (Page 56)

Chapter 2: Reporting codes
52 NX-8E Control Panel Installation Manual
Location 174
Zones 65 to 72 zone
types Location 174 has eight segments of numerical data. Use this location
to program the zone type for zones 65 to 72. Use segment 1 for zone
65, segment 2 for zone 66, etc. The segment defaults are 6, 6, 6, 6, 6,
6, 6, 6.
Location 175
Zones 65 to 72 partition Location 175 has eight segments of feature selection data. Use this
location to select the partitions (1 to 8) that zones 65 to 72 reside in.
Each segment corresponds to a zone (segment 1 to zone 65,
segment 2 to zone 66, etc.). In each segment, enter 1 for partition 1
through 8 for partition 8.
Location 176
Zones 73 to 80 zone
types Location 176 has eight segments of numerical data. Use this location
to program the zone type for zones 73 to 80. Use segment 1 for zone
73, segment 2 for zone 74, etc. The segment defaults are 6, 6, 6, 6, 6,
6, 6, 6.
Location 177
Zones 73 to 80 partition Location 177 has eight segments of feature selection data. Use this
location to select the partitions (1 to 8) that zones 73 to 80 reside in.
Each segment corresponds to a zone (segment 1 to zone 73,
segment 2 to zone 74, etc.). In each segment, enter 1 for partition 1
through 8 for partition 8.
Location 178
Zones 81 to 88 zone
types Location 178 has eight segments of numerical data. Use this location
to program the zone type for zones 81 to 88. Use segment 1 for zone
81, segment 2 for zone 82, etc. The segment defaults are 6, 6, 6, 6, 6,
6, 6, 6.
Location 179
Zones 81 to 88 partition Location 179 has eight segments of feature selection data. Use this
location to select the partitions (1 to 8) that zones 81 to 88 reside in.
Each segment corresponds to a zone (segment 1 to zone 81 segment
2 to zone 82, etc.). In each segment, enter 1 for partition 1 through 8
for partition 8.
Location 180
Zones 89 to 96 zone
types Location 180 has eight segments of numerical data. Use this location
to program the zone type for zones 89 to 96. Use segment 1 for zone
89, segment 2 for zone 90, etc. The segment defaults are 6, 6, 6, 6, 6,
6, 6, 6.
Location 181
Zones 89 to 96 partition Location 181 has eight segments of feature selection data. Use this
location to select the partitions (1 to 8) that zones 89 to 96 reside in.
Each segment corresponds to a zone (segment 1 to zone 89,
segment 2 to zone 90, etc.). In each segment, enter 1 for partition 1
through 8 for partition 8.
Location 182
Zones 97 to 104 zone
types Location 182 has eight segments of numerical data. Use this location
to program the zone type for zones 97 to 104. Use segment 1 for zone
97, segment 2 for zone 98, etc. The segment defaults are 6, 6, 6, 6, 6,
6, 6, 6.
Location 183
Zones 97 to 104 partition Location 183 has eight segments of feature selection data. Use this
location to select the partitions (1 to 8) that zones 97 to 104 reside in.
Each segment corresponds to a zone (segment 1 to zone 97,
segment 2 to zone 98, etc.). In each segment, enter 1 for partition 1
through 8 for partition 8.