Panasonic AG-DP800HP User Manual
Instructions, Panasonic
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Table of contents
Document Outline
- Instructions
- Panasonic
- Professional/Industrial Video
- Model AG-
- <
- S'
- POWER Switch
- MODE CHECK Button
- BREAKER Button (Bottom panel)
- Earphone jack
- Audio Input Connectors fm 26P VTR Connector
- Speaker
- Audio Monitor Level Control
- Viewfinder
- Shoulder Strap Mount
- Power Selector Switch
- External DC Input Socket
- AUDIO OUT Connectors (Phono jacks)
- VTR VIDEO OUT Connector (Y/C)
- VTR VIDEO OUT Connector (BNC)
- S'
- EE
- EE
- Viewfinder display
- Automatic Iris Controi
- Lens Iris Selector Switch [IRIS]
- Power Zoom Control Switch
- Hand Strap
- Return Switch [RET/REC CHECK]
- VTR Start/Stop Switch
- Lens Cable (12-pin) Focus Ring Zoom Ring
- Qj] Iris Ring
- Flange Back Control Ring Macro Ring
- Flange back clamp knob
- Power/Manual Zoom Selector Switch
- Remove the microphone of the main unit.
- Attach the microphone holder.
- Remove the battery holder from the main unit.
- Insert the lithium battery into the battery holder.
- (Make sure the “+” and polarities are aligned properly.)
- With the triangular marks on the main unit and on the battery holder facing each other, fit the battery holder back into the main unit.
- NOTE
- Initializing the Memory and Setting the Date and Time
- Set the POWER switch to ON.
- When the MENU ON/OFF selector switch is set to ON, the setting screen (MENU) appears in the viewfinder.
- While monitoring the viewfinder display, press the SHIFT button until the arrow at the far left is aligned with “DIAGNOSIS”.
- When the START button is pressed, the self-diagnosis (DIAGNOSIS) screen appears.
- Press the SHIFT button until the arrow at the far left is aligned with “MEMORY INIT.?”.
- Press the START button.
- Press the SHIFT button until the arrow at the far left is aligned with “PREVIOUS MENU”,
- When the START button is pressed, the MAIN MENU appears.
- Press the SHIFT button until the arrow at the far left is aligned with “TIME/DATE”. ■ •
- When the START button Is pressed, the calender and clock setting screen appears.
- Initializing the memory and setting the date and time (Continued)
- Using The AU-BP402 Battery Pack
- Remove the Anton/Bauer battery holder.
- Connect the cable from the camera recorder to the cable of the AU-M402 battery case.
- Use a screwdriver to mount the AU-M402 on the camera recorder.
- Connect the battery pack’s plug to the connector inside the battery * case, and insert the battery pack into the case.
- Set menu item 7 “BATTERY” (battery selection) to “Ni-Cd 12 V”,
- Connect the camera recorder’s external DC input socket to the DC OUT connector on the AU-B110 AC adaptor.
- Turn on the AC adaptor’s power.
- Set the camera recorder’s power switch to ON.
- Attach the Anton/Bauer battery pack.
- Set menu item 7 “BATTERY” (battery selection) to the battery which is going to be used.
- REFERENCE
- Remove the battery holder made by Anton/Bauer.
- Mount the screws for the accessory battery installation terminal (NP-1).
- Install the battery holder made by Sony.
- When supplying power from the 26P VTR connector
- Using The AU-BP402 Battery Pack
- Black Balance & White Balance Adjustments (Continued)
- Shoot a white object so that it is virtually at the center of the screen and occupies an area equivalent to at least one-fourth of the height and width of the screen, and set the AUTO W/B BAL switch to AWB,
- NOTES
- REFERENCE
- Press the VTR START/STOP button to start the recording.
- Press the VTR START/STOP button to suspend the recording.
- NOTE
- Press the PLAY button.
- Press the PLAY button again where the new cut is to be joined onto the existing recording.
- ■ B To start the recording, press the VTR START/STOP button again.
- NOTE
- Select the desired input signals using the audio input selector switches.
- Turn the audio level controls clockwise or counterclockwise and adjust them so that the audio signal levels indicated on the display’s level meter are brought to the standard positions.
- Set the POWER switch to the ON position.
- Press the STOP button.
- Press the PLAY button.
- The playback pictures appear on the viewfinder and on a TV monitor which has been connected to the camera recorder.
- Automatic S-VHS/VHS identification and playback
- Tracking
- AUDIO SELECT switch
- Cue and Review Playback
- Still picture playback
- NOTE
- Set the TC/UB/COUNTER selector switch to TC or UB.
- Set the data.
- REFERENCE
- Set the camera recorder to the eject, rec pause or stop mode.
- Set the MENU ON/OFF selector switch to ON.
- Press the SHIFT button to select the desired menu item.
- Press the START button.
- Press the SHIFT button to select a sub menu item.
- Press the SET + or SET — button to change the data setting.
- To return to the main menu and perform settings on another menu item, press the SHIFT button to move the cursor (arrow) to the previous menu, and press the START button,
- To exit from the menu settings, set the MENU ON/OFF selector switch to OFF.
- NOTE
- NOTE
- Menu Items (Continued)
- Menu Items (Continued)
- Panasonic
- Panasonic