beautypg.com

Coils table – Red Lion DLC User Manual

Page 26

background image

40011/40027

26

COILS TABLE

COIL ADDRESS

COIL NAME

ACCESS

COMMENTS

1

Calibration Checksum Error

40505 (bit 0)

Read/Write

2

Parameter Checksum Error

40505 (bit 1)

Read/Write

3

40505 (bit 2)

Read/Write

4

40503

Read/Write 1 = Disables writes to the non-volatile memory; Returns to 0(writes are enabled) at

power cycle.

CH A

CH B

5

17

Shorted RTD Input Error

40504

Read Only 1 = Shorted RTD; Causes process value to be -32002, disables alarms, sets control

output(s) to sensor failure power preset level, causes flashing LEDs.

6

18

40504

Read Only 1 = Input Error; Causes process value to be 32002, disables alarms, sets control

output(s) to sensor failure power preset level, causes flashing LEDs.

7

19

Process Value (<-32000)
Under Range Input Error

Signal or Sensor Under
Range Input Error

40504

40504

Read Only

Read Only 1 = Under Range Error; Causes process value to be -32001, maintains control

output at present level, causes flashing LEDs.

8

20

Process Value (>32000)
Over Range Input Error

Signal or Sensor Over
Range Input Error

40504

40504

Read Only

Read Only 1 = Over Range Error; Causes process value to be 32001, maintains control output

at present level, causes flashing LEDs.

9

21

Control Output OP1 State

40014/40030

Read Only 0 = Off, 1 = On

10

22

Alarm 1 Output AL1 State

40015/40031

Read/Write 0 = Off, 1 = On; A write of 1 is only possible when alarm is set for Manual.

11

23

40016/40032

Read/Write 0 = Off, 1 = On; A write of 1 is only possible when alarm is set for Manual.

12

24

Control Mode

40041/40049

Read/Write 0 = Automatic Mode, 1 = Manual Mode

13

25

Disable Setpoint Ramping

40042/40050

Read/Write 0 = Enabled, 1 = Disabled

14

26

Setpoint Ramping In Process

40043/40051

Read Only 0 = No, 1 = Yes

15

27

Disable Integral Action

40044/40052

Read/Write 0 = Enabled, 1 = Disabled

33

31

30

29

16

32

28

Local/Remote Setpoint Select

Advance Profile Phase

SETPOINT CONTROLLER MODEL ONLY

Auto-Tune Start

40046

40070/40078

40505 (bit 5)

40505 (bit 4)

40011/40027

Read/Write

Read/Write

Read/Write

Read/Write

Read/Write

0 = Local Setpoint; 1 = Remote Setpoint

1 = Advance running Profile to next phase

1 = Checksum Error in A or B Setpoint Controller Operating Status memory, disables
control and alarm outputs, causes flashing LEDs, and aborts profile putting channel
in manual control at 0% power.

0 = Stop, 1 = Start

INPUT TYPE REGISTER (40101/40201) TABLE

ANALOG OUTPUT ASSIGNMENT REGISTER
(400301/40309) TABLE

SERIAL BAUD RATE REGISTER (40402) TABLE

ALARM 1 (40131/40231) AND ALARM 2
(40136/40236) ACTION REGISTER TABLE

MODE

TYPE

0

Thermocouple - T

1

Thermocouple - E

2

Thermocouple - J

3

Thermocouple - K

4

Thermocouple - R

5

Thermocouple - S

6

Thermocouple - B

8

7

Thermocouple - C

Thermocouple - N

Process Current, Square Root Ext.

Process Current

17

16

15

Process Voltage

14

Linear mV (1 = 10mV)

13

Linear Ohms

12

RTD nickel 672

11

RTD platinum 392

10

RTD platinum 385

9

TYPE

MODE

MODE

ASSIGNMENT

0

Output Power A

1

Process Value A

2

Setpoint A

3

Ramping Setpoint A

4

Deviation A

5

Direct Entry Value 1

6

Output Power B

7

Process Value B

8

Setpoint B

9

Ramping Setpoint B

10

Deviation B

11

Direct Entry Value 2

MODE

ACTION

0

Manual

1

Absolute HI (Balanced)

2

Absolute LO (Balanced)

3

Absolute HI (Unbalanced)

4

Absolute LO (Unbalanced)

5

Deviation HI

6

Deviation LO

7

Band Inside Acting

8

Band Outside Acting

9

Cooling (Alarm 2 only)

MODE

BAUD

0

300

1

600

2

1200

3

2400

4

4800

5

9600

6

19200

7

38400

Integral and Offset/Manual
Power Checksum Error

MIRROR REGISTER

Alarm 2 Output AL2/OP2 State

1 = Under Range Error; Causes process value to be -32003, maintains control
output at present level until input causes Sensor FailurePower Preset Level, causes
flashing LEDs.

1 = Over Range Error; Causes process value to be 32003, maintains control output
at present level until input causes Sensor FailurePower Preset Level, causes
flashing LEDs.

Open Thermocouple, RTD, or
Extreme Process Input Over/
Under Range Input Error

Non-Volatile Memory Write
Disable

Setpoint Controller Segment
Memory Checksum Errror

Setpoint Controller Status
Memory Checksum Error

1 = Checksum Error in A or B Setpoint Controller Segment memory (40601-40760),
causes process value to be 32100 disables control and alarm outputs, causes
flashing LEDs.

1 = Error; Causes Process Value to be 32100, Disables control and alarm outputs,
causes flashing LEDs. Writing a zero clears the error.

1 = Error; Causes Process Value to be 32100, Disables control and alarm outputs,
causes flashing LEDs. Writing a zero clears the error.

1 = Error; Causes Process Value to be 32100, Disables control and alarm outputs,
causes flashing LEDs. Writing a zero clears the error.

Process Voltage, Square Root Ext.