KROHNE MFC 400 FOUNDATION FIELDBUS - Manual (Page 74)

4
OPERATION
74
MFC 400
www.krohne.com 11/2013 - 4003221901 - AD MFC 400 FF R01 en
Value R/W Setting:
0: Forward / 1: Reverse
Forward
REV_FLOW2 REV_FLOW2 REV_FLOW2 REV_FLOW2
Reverse Flow 2 Reverse Flow 2 Reverse Flow 2 Reverse Flow 2
R/W Indicates reverse flow when true. -
Status R/W Setting:
Good Non Cascade / Good Cascade / Uncertain / Bad Not
Connected / Bad / Bad No Comm with Last Useable Value
(LUV)
Bad Not Connected
Value R/W Setting:
0: Forward / 1: Reverse
Forward
RTOTAL RTOTAL RTOTAL RTOTAL
Rejected Total Rejected Total Rejected Total Rejected Total
R/W Indicates the Totalization of BAD or BAD + UNCERTAIN Inputs,
according to INTEG_OPTS.
0.0
SRTOTAL SRTOTAL SRTOTAL SRTOTAL
Snapshot of Snapshot of Snapshot of Snapshot of
Rejected Total Rejected Total Rejected Total Rejected Total
R The snapshot of RTOTAL, just before a reset. 0.0
SSP SSP SSP SSP
Snapshot of Snapshot of Snapshot of Snapshot of
Setpoint Setpoint Setpoint Setpoint
R The snapshot of TOTAL_SP. 0.0
STATUS_OPTS STATUS_OPTS STATUS_OPTS STATUS_OPTS
Status Option Status Option Status Option Status Option
R/W Options which the user may select in the block processing of
status.
Uninitialized
Setting:
Uncertain if Man
STOTAL STOTAL STOTAL STOTAL
Snapshot of Total Snapshot of Total Snapshot of Total Snapshot of Total
R Indicates the Snapshot of OUT just before a reset. 0.0
TIME_UNIT1 TIME_UNIT1 TIME_UNIT1 TIME_UNIT1
Time Unit 1 Time Unit 1 Time Unit 1 Time Unit 1
R/W Converts the rate time units in seconds. Uninitialized
Setting:
1: seconds / 2: minutes / 3: hour / 4: days
TIME_UNIT2 TIME_UNIT2 TIME_UNIT2 TIME_UNIT2
Time Unit 2 Time Unit 2 Time Unit 2 Time Unit 2
R/W Converts the rate time units in seconds. Uninitialized
Setting:
1: seconds / 2: minutes / 3: hour / 4: days
TOTAL_SP TOTAL_SP TOTAL_SP TOTAL_SP
Total Setpoint Total Setpoint Total Setpoint Total Setpoint
R/W The SP for a batch totalization. Not just SP because SP has PV
units and other special properties not used in this application.
0
Setting:
Positive or 0
UNIT_CONV UNIT_CONV UNIT_CONV UNIT_CONV
Unit Conversion Unit Conversion Unit Conversion Unit Conversion
R/W Factor to convert the engineering units of input 2 into the
engineering units of input 1.
1.0
Setting:
Positive or not 0
UPDATE_EVT UPDATE_EVT UPDATE_EVT UPDATE_EVT
Update Event Update Event Update Event Update Event
R This alert is generated by any change to the static data. -
Unacknowledged R A discrete enumeration which is set to "Unacknowledged"
when an alarm occurs, and set to "Acknowledged" by a write
from a human interface device or other entity which can
acknowledge that the alarm/event has been noticed.
Uninitialized
Setting:
Uninitialized / Acknowledged / Unacknowledged
Update State R A discrete enumeration which gives an indication of whether
the alert is active and whether it has been reported.
Uninitialized
Setting:
Uninitialized / Acknowledged / Unacknowledged
Parameter Parameter Parameter Parameter
DD name Access Description and settings Initial Value