KROHNE MFC 400 FOUNDATION FIELDBUS - Manual (Page 48)

4
OPERATION
48
MFC 400
www.krohne.com 11/2013 - 4003221901 - AD MFC 400 FF R01 en
SENSOR_SN SENSOR_SN SENSOR_SN SENSOR_SN
Sensor Serial
Number
R The sensor serial number. -
SENSOR_TYPE SENSOR_TYPE SENSOR_TYPE SENSOR_TYPE
Sensor Type
R The type of sensor. Coriolis
(Gyroscopic
Settings:
Coriolis (Gyroscopic
SET_OPERATE_ SET_OPERATE_ SET_OPERATE_ SET_OPERATE_
MODE MODE MODE MODE
Operation Mode
R/W Sets the operating mode of the sensor (Fct. A9). 3: Measuring
Settings:
1:Stop / 2:Startup / 3:Measuring / 5:Standby / 6:Calibrate Zero
STD_DENSITY_K0 STD_DENSITY_K0 STD_DENSITY_K0 STD_DENSITY_K0
Standard Density
k0
R/W Sets k0 value for standard density (Fct. C1.2.6). 346.4
Settings:
0.0...5000.00
STD_DENSITY_K1 STD_DENSITY_K1 STD_DENSITY_K1 STD_DENSITY_K1
Standard Density
k1
R/W Sets k1 value for standard density (Fct. C1.2.7). 0.439
Settings:
-100.00…100.00
STD_DENSITY_K2 STD_DENSITY_K2 STD_DENSITY_K2 STD_DENSITY_K2
Standard Density
k2
R/W Sets k2 value for standard density (Fct. C1.2.8). 0.0
Settings:
-10.00…10.00
STD_DENSITY_ STD_DENSITY_ STD_DENSITY_ STD_DENSITY_
TEMP TEMP TEMP TEMP
Standard Density
Temp.
R/W Set reference temperature for standard density (Fct. C1.2.5). 20.0 °C
Settings:
-245.0…500.0 °C
TEMPERATURE TEMPERATURE TEMPERATURE TEMPERATURE
Temperature
The measured value and status available to the Function
Block.
-
STATUS
Status
R Digital transducers, unlike their analogue versions, can detect
faults that make the measurement bad or prevent the
actuator from responding. This additional, valuable
information will be passed along with each transmission of a
data value in the form of a status attribute.
-
VALUE
Value
R A numerical quantity entered by a user or calculated by the
algorithm.
-
TEMPERATURE_ TEMPERATURE_ TEMPERATURE_ TEMPERATURE_
RANGE RANGE RANGE RANGE
Temperature
Range
R The High and Low range limit values, the engineering units
code and the number of digits to the right of the decimal point
to be used to display the Primary Value.
-
EU_100
max value
R The engineering unit value which represents the upper end of
range of the associated block parameter.
500.0
EU_0
min value
R The engineering unit value which represents the lower end of
range of the associated Block Parameter.
-200.0
UNITS_INDEX
Units Index
R/W Device Description units code index for the engineering unit
descriptor for the associated block value.
° C
Settings:
K; °C; °F
DECIMAL
Decimal (Point)
R The number of digits to the right of the decimal point which
should be used by an interface device in displaying the
specified parameter.
2
TRANSDUCER_ TRANSDUCER_ TRANSDUCER_ TRANSDUCER_
DIRECTORY DIRECTORY DIRECTORY DIRECTORY
Transducer
Directory Entry
A directory that specifies the number and starting indices of
the data collections in the transducer block.
0
TRANSDUCER_ TRANSDUCER_ TRANSDUCER_ TRANSDUCER_
TYPE TYPE TYPE TYPE
Transducer Type
R Identifies the transducer that follows. Other
Parameter Parameter Parameter Parameter
DD name Access Description and settings Initial Value