Operation – KROHNE MFC 400 FOUNDATION FIELDBUS User Manual
Page 54
4
OPERATION
54
MFC 400
www.krohne.com
11/2013 - 4003221901 - AD MFC 400 FF R01 en
PRIMARY_VALUE_
PRIMARY_VALUE_
PRIMARY_VALUE_
PRIMARY_VALUE_
204
204
204
204
Conc. MassFlow 2
The measured value and status available to the Function
Block.
-
STATUS
Status
R
Digital transducers, unlike their analogue versions, can detect
faults that make the measurement bad or prevent the
actuator from responding. This additional, valuable
information will be passed along with each transmission of a
data value in the form of a status attribute.
-
VALUE
Value
R
A numerical quantity entered by a user or calculated by the
algorithm.
-
PRIMARY_VALUE_
PRIMARY_VALUE_
PRIMARY_VALUE_
PRIMARY_VALUE_
RANGE_204
RANGE_204
RANGE_204
RANGE_204
Conc. MassFlow 2
Range
The high and low range limit values, the engineering units
code and the number of digits to the right of the decimal point
to be used to display the Primary Value.
-
EU_100
max value
R
The engineering unit value which represents the upper end of
range of the associated Block Parameter.
NaN
EU_0
min value
R
The engineering unit value which represents the lower end of
range of the associated Block Parameter.
-NaN
UNITS_INDEX
Units Index
R/W
Device Description units code index for the engineering unit
descriptor for the associated block value.
kg/s
Settings:
Mass flow units:
Mass flow units:
Mass flow units:
Mass flow units:
kg/s; kg/min; kg/h; kg/d; t/s; t/min; t/h; t/d; g/s; g/min; g/h;
g/d; lb/s; lb/min; lb/h; lb/d; klb(US)/s; klb(US)/min; klb(US)/h;
klb(US)/d; STon/s; STon/min; STon/h; STon/d; LTon/s;
LTon/min; LTon/h; LTon/d
DECIMAL
Decimal (Point)
R
The number of digits to the right of the decimal point which
should be used by an interface device in displaying the
specified parameter.
2
PRIMARY_VALUE_
PRIMARY_VALUE_
PRIMARY_VALUE_
PRIMARY_VALUE_
205
205
205
205
Conc. Vol.Flow 1
The measured value and status available to the Function
Block.
-
STATUS
Status
R
Digital transducers, unlike their analogue versions, can detect
faults that make the measurement bad or prevent the
actuator from responding. This additional, valuable
information will be passed along with each transmission of a
data value in the form of a status attribute.
-
VALUE
Value
R
A numerical quantity entered by a user or calculated by the
algorithm.
-
PRIMARY_VALUE_
PRIMARY_VALUE_
PRIMARY_VALUE_
PRIMARY_VALUE_
RANGE_205
RANGE_205
RANGE_205
RANGE_205
Conc. Vol.Flow 1
Range
The high and low range limit values, the engineering units
code and the number of digits to the right of the decimal point
to be used to display the Primary Value.
-
EU_100
max value
R
The engineering unit value which represents the upper end of
range of the associated Block Parameter.
NaN
EU_0
min value
R
The engineering unit value which represents the lower end of
range of the associated Block Parameter.
-NaN
UNITS_INDEX
Units Index
R/W
Device Description units code index for the engineering unit
descriptor for the associated block value.
m³/h
Settings:
Volume flow units:
Volume flow units:
Volume flow units:
Volume flow units:
m³/s; m³/min; m³/h; m³/d; L/s; L/min; L/h; L/d; kL/s; kL/min;
kL/h; kL/d; mL/min; CFS; CFM; CFH; ft³/d; kCFS; kCFM;
kCFH; kft³/d; cm³/s; cm³/min; cm³/h; cm³/d; gal/s; GPM;
gal/h; gal/d; kgal/s; kgal/min; kgal/h; kgal/d; bbl/s; bbl/min;
bbl/h; bbl/d; ImpGal/s; ImpGal/min; ImpGal/h; ImpGal/d
Parameter
Parameter
Parameter
Parameter
DD name
Access
Description and settings
Initial Value