KROHNE OPTIWAVE 7300C EN - Manual (Page 66)

6
OPERATION
66
OPTIWAVE 7300 C
www.krohne.com 03/2014 - 4000172405 - HB OPTIWAVE 7300 R07 en
C.3.5 Error Handling This sets the behaviour of current
output 1 if an error occurs. Hold means
that the output current stays at the
value where the error occurred. Hold is
not available if 3.8…20.5 mA (NAMUR)
is the output range.
3.6 mA, 22 mA, Hold 22 mA
Error Handling
Delay
The time after which the current output
changes to an error value. It shows
that there is a measurement error.
min.-max:
0…900 sec (seconds)
10 sec
C.3.6 HART Address
Any HART ® address greater than 0 will
activate HART ® multidrop mode.
min.-max: 0…15 0
C.4 Output 2 (Passive)
C.4.1 Output
Function
Select an output function to scale the
current values. This is not displayed in
the operator mode.
Level, Distance, Volume
(Mass), Ullage Volume (Ullage
Mass), Reflection
Level
C.4.2 4 mA Setting Give a measurement value to 4 mA. min.-max: 1 0 m / 0 ft
C.4.3 20 mA Setting Give a measurement value to 20 mA. min.-max: 2 Depends on the
output function
C.4.4 Output Range Sets the effective range of output 2
either with or without over-run.
min.-max: 3.8…20.5 mA
(NAMUR), 4…20 mA
4…20 mA
C.4.5 Error Handling This sets the behaviour of current
output 2 if an error occurs. Hold means
that the output current stays at the
value where the error occurred. Hold is
not available if 3.8…20.5 mA (NAMUR)
is the output range.
3.6 mA, 22 mA, Hold 22 mA
Error Handling
Delay
The time after which the device shows
there is a measurement error. This
value is set in the output 1 menu.
Read only Refer to
function C.3.5
C.5 Device Setup
C.5.1 C.5.1 C.5.1 C.5.1 Display Display Display Display
Settings Settings Settings Settings
To display the information you need, To display the information you need, To display the information you need, To display the information you need,
refer to these menu items. refer to these menu items. refer to these menu items. refer to these menu items.
C.5.1.1 Language Information can be displayed in any of
the 9 languages stored in the device. If
it is necessary to change the display
quickly to English, push [ ] for 3
seconds in operator mode.
English, French, German,
Italian, Japanese, Chinese
(simplified), Portuguese,
Russian, Spanish
C.5.1.2 Display Mode The display screen status will change
after the time given in C.5.1.3. (time
delay). Disable Disable Disable Disable switches off this
functionality, Auto-Off Auto-Off Auto-Off Auto-Off switches off the
display and Default Screen Default Screen Default Screen Default Screen will show
the selected default screen. To set to
the default screen, push [ ] for 1
second in the operator mode.
Disable, Auto-Off, Default
Screen
Disable
C.5.1.3 Time Delay The time after which the display will
switch to the status set in C.5.1.2
(Display Mode).
1, 3, 5, 10 (minutes) 1
Contrast The contrast control for the display
screen. You can select a shade of gray
between light gray (level 1) and black
(level 9).
Level 1, Level 2, Level 3, Level
4, Level 5, Level 6, Level 7,
Level 8, Level 9
Level 5
C.5.1.4 Length Unit The length unit displayed in operator
mode.
m, cm, mm, inch, ft, ft-inch-
1/16inch, ft-inch-1/32inch,
Free Unit
m
Menu
No.
Function Function description Selection list Default