B.70 system:beep command, B.71 system:communication:gpib:address command, B.72 system:communication:gpib:address? query – KEPCO BHK-MG 200W (Full Rack) Series User Manual

Page 147: B.73 system:communication:serial:baud command, B.74 system:communication:serial:baud? query, B.75 system:communication:serial:echo command, B.76 system:communication:serial:echo? query, B.77 system:communication:serial:pace command, B.70, System:beep

BHK-MG (OPR) 022014

B-17

B.70 SYSTem:BEEP COMMAND

SYST:BEEP

Syntax:

Short Form: SYST:BEEP

Long Form: SYSTem:BEEP

Description:Causes the unit to emit a brief audible tone

B.71 SYSTem:COMMunication:GPIB:ADDRess

COMMAND

SYST:COMM:GPIB:ADDR

Syntax:

Short Form: SYST:COMM:GPIB:ADDR 1 to 30
Long Form: SYSTem:COMMunication:GPIB:ADDRess 1 to 30

Description: Sets selected power supply GPIB address. See PAR. 3.3.6.2 and Figure 3-2 for special program-

ming considerations.

B.72 SYSTem:COMMunication:GPIB:ADDRess? QUERY

SYST:COMM:GPIB:ADDR?

Syntax:

Short Form: SYST:COMM:GPIB:ADDR?
Long Form: SYSTem:COMMunication:GPIB:ADDRess?
Return Value: 1 to 31

Description: Sets selected power supply GPIB address.

B.73 SYSTem:COMMunication:SERial:BAUD COMMAND

SYST:COMM:SER:BAUD

Syntax:

Short Form: SYST:COMM:SER:BAUD {19200 | 9600 | 4800 | 2400}
Long Form: SYSTem:COMMunication:SERial:BAUD {19200 | 9600 | 4800 | 2400}

Description: Sets the unit to operate at the specified baud rate. See PAR. 3.3.6.2 and Figure 3-2 for special pro-

gramming considerations.

B.74 SYSTem:COMMunication:SERial:BAUD? QUERY

SYST:COMM:SER:BAUD?

Syntax:

Short Form: SYST:COMM:SER:BAUD?
Long Form: SYSTem:COMMunication:SERial:BAUD?
Return Value: {19200 | 9600 | 4800 | 2400}

Description: Returns operating baud rate.

B.75 SYSTem:COMMunication:SERial:ECHO COMMAND

SYST:COMM:SER:ECHO

Syntax:

Short Form: SYST:COMM:SER:ECHO {ON | OFF} or {01 | 00}
Long Form: SYSTem:COMMunication:SERial:ECHO {ON | OFF} or {01 | 00}

Description: Enables (ON) or disables (OFF) echo mode (see PAR. 3.4.3.1). Sending ON or 01 causes all sub-

sequent characters to be echoed back. Sending OFF or 00 turns off the character echo after the next
line terminator character. The *RST command has no effect on echo status. See PAR. 3.3.6.2 and Fig-
ure 3-2 for special programming considerations.

B.76 SYSTem:COMMunication:SERial:ECHO? QUERY

SYST:COMM:SER:ECHO?

Syntax:

Short Form: SYST:COMM:SER:ECHO?
Long Form: SYSTem:COMMunication:SERial:ECHO?
Return Value: {01 | 00}

Description: Returns 01 when echo mode is active (ON) or 00 when disabled (OFF) (see PAR. 3.4.3.1).

B.77 SYSTem:COMMunication:SERial:PACE COMMAND

SYST:COMM:SER:PACE

Syntax:

Short Form: SYST:COMM:SER:PACE {NONE | XON}
Long Form: SYSTem:COMMunication:SERial:PACE {NONE | XON}

Description: Enables (XON) or disables (NONE) data flow control via the serial interface (see PAR. 3.4.3.3).

See PAR. 3.3.6.2 and Figure 3-2 for special programming considerations.