Rice Lake Condec UMC600 - Manual (Page 49)

46 UMC600 Installation Manual
4.12.3 Serial Command Option Parameters
The following table lists the option parameter serial commands for the UMC600.
Option 1 K0306 00 = TI (time entry) K0701 00 = Off K0717 00 = Off K0906 00 = CHG
K0100 00 = Off K0306 01 = DA (date entry) K0701 01 = On K0717 01 = On K0906 01 = OFF
K0100 01 = On K0906 02 = RCL
Option 4 K0702 00 = Off K0718 00 = Off
Option 2 K0400 00 = Off K0702 01 = On K0718 01 = On Option 10
K0200 00 = Off K0400 01 = On K1000 00 = Off
K0200 01 = On K0401 00 = Off K0703 00 = Off K0719 00 = ODD K1000 01 = On
K0201 00 = DSP K0401 01 = 1 K0703 01 = On K0719 01 = EVN K1001 00 = DSP
K0201 01 = GR K0401 02 = 2 K0719 02 = SPC K1001 01 = GR
K0201 02 = NET K0401 03 = 3 K0704 00 = Off K0719 13 = ONE K1001 02 = NET
K0401 04 = 4 K0704 01 = On
K0202 00 = P.1 K0401 05 = 5 K0720 00 = Off K1002 00 = DSP
K0202 01 = P.2 K0401 06 = 6 K0705 00 = Off K0720 01 = On K1002 01 = GR
K0401 07 = 7 K0705 01 = On K1002 02 = NET
K0203 00 = Off K0401 08 = 8 Option 8
K0203 01 = DE K0401 09 = 9 K0706 00 = Off K0800 00 = Off K1003 00 = OFF
K0203 02 = CO K0401 10 = 10 K0706 01 = On K0800 01 = On K1003 01 = GR
K0401 11 = 20 K0801 00 = DSP K1003 02 = NET
K0204 00 = 12 K0401 12 = 30 K0707 00 = Off K0801 01 = GR
K0204 01 = 24 K0401 13 = 40 K0707 01 = On K0801 02 = DSP K1004 00 = OFF
K0204 02 = 48 K0401 14 = 50 K1004 01 = 0
K0204 03 = 96 K0708 00 = Off K0802(xxxxxxxx) – Zero K1004 02 = 1
Option 5 K0708 01 = On K0803(xxxxxxxx) – Span K1004 03 = 2
K0205(xxxxxxxx)–Zero K0500 00 = Off K0804(xxxxxxxx) – Zero Trim K1004 04 = 3
K0206(xxxxxxxx)–Span K0500 01 = On K0709 00 = Off K0805(xxxxxxxx) – span trim K1004 05 = 4
K0207(xxxxxxxx)–Zero Trim K0501 00 = TAG K0709 01 = On K1004 06 = 5
K0208(xxxxxxxx)–Span Trim K0501 01 = LAN Option 9 K1004 07 = 6
K0501 02 = OFF K0710 00 = Off K0900 00 = Off K1004 08 = 7
Option 3 K0710 01 = On K0900 01 = On K1004 09 = 8
K0300 00 = Off K0502 00 = Addr (RS-485
address entry)
K0901 00 = Off K1004 10 = 9
K0300 01 = On K0711 00 = Off K0901 01 = On K1004 11 = 10
K0301 00 = STD K0503 00 = Off K0711 01 = On K1004 12 = 20
K0301 01 = DLS K0503 01 = On K0902 00 = Off K1004 13 = 30
K0712 00 = Off K0902 01 = On K1004 14 = 40
K0302 00 = 24 K0504 00 = Off K0712 01 = On K1004 15 = 50
K0302 01 = 12 K0504 01 = Off K0903 00 = Off
K0713 00 = Off K0903 01 = On Option 11
K0303 00 = A K0505 00 = Cnt (num entry) K0713 01 = On K1100 00 = Off
K0303 01 = P K0904 00 = Off K1100 01 = On
Option 6 K0714 00 = Off K0904 01 = On K1101 00 = ZER
K0304 00 = Ab K0600 00 = Off K0714 01 = On K1101 01 = N-G
K0304 01 = On K0600 01 = On K0905 00 = CHG K1101 02 = TAR
K0304 02 = Un K0715 00 = Off K0905 01 = OFF K1101 03 = PRT
Option 7 K0715 01 = On K0905 02 = RCL K1101 04 = STA
K0305 00 = No. K0700 00 = Off K1101 05 = PAU
K0305 01 = Let K0700 01 = On K0716 00 = Off K1101 06 = ABO
K0716 01 = On (K1102 - 05 same as K1101)
Table 4-25. Serial Command Option Parameter Codes