Rice Lake Condec UMC600 - Manual (Page 22)

Configuration 19
3.1.4 Normal Configuration Setup Parameters
You must be in the configuration mode (SW1-2 closed to set the indicator from the PC) to be able to write
configuration parameters. To write commands the following
Jxxyyzz sequence must be used. The following
parameters and their setup numbers are as follows:
Parameter 1 = Grads J0600 03 = Both J1100 02 = Ov.Un J1103 06 = 6 J1200 14 = 50
J0100 00 = 500 J1101 00 = HL J1103 07 = 7
J0100 01 = 1000 Parameter 7 = AZM Capture J1101 01 = TGT J1103 08 = 8 Parameter 13 = Truck in/out
J0100 02 = 1500 J0700 00 = Off J1103 09 = 9 J1300 00 = Nor
J0100 03 = 2000 J0700 01 = .5 J1102 00 = Pos J1103 10 = 10 J1300 01 = Tru
J0100 04 = 2500 J0700 02 = 1 J1102 01 = Zer J1301 00 = Can
J0100 05 = 3000 J0700 03 = 3 J1103 00 = Off J1301 01 = Str
J0100 06 = 4000 J1103 00 = Pos J1103 01 = 1
J0100 07 = 5000 Parameter 8 = Zero Range J1103 01 = Zer J1103 02 = 2 J1302 00 = Off
J0100 08 = 6000 J0800 00 = 1.9 J1103 03 = 3 J1302 01 = On
J0100 09 = 8000 J0800 01 = FS J1104 00 = Pos J1103 04 = 4.
J0100 10 = 10000 J1104 01 = Zer Parameter 14 = Serial
J0100 11 = 12000 Parameter 9 = Motion Band J1104 00 = Off J1400 00 = Off
J0100 12 = 14000 J0900 00 = Off J1100 03 = Bat 1 J1104 01 = S1 J1400 01 = SI
J0100 13 = 16000 J0900 01 = 1 J1101 00 = Off J1104 02 = S1.P J1400 02 = DU
J0100 14 = 18000 J0900 02 = 3 J1101 01 = S1 J1104 03 = S1.D (J1401 – 1405 for SI and DU)
J0100 15 = 20000 J0900 03 = 5 J1101 02 = S1.P J1104 04 = S.P.D. J1401 00 = Net
J0900 04 = 10 J1101 03 = S1.D J1401 01 = GTN
Parameter 2 = Resolution J1101 04 = S.P.D. J1105 00 = Pos
J0200 00 = 1 Parameter 10 = Units J1105 01 = Zer J1402 00 = Off
J0200 01 = 2 J1000 00 = Lb only J1102 00 = Pos J1402 01 = 1
J0200 02 = 5 J1000 01 = Kg only J1102 01 = Zer J1106 00 = Off J1402 02 = 2
J0200 03 = 10 J1000 02 = Lb/Kg Conversion J1106 01 = 1 J1402 03 = 3
J0200 04 = 20 J1103 00 = Off J1106 02 = 2 J1402 04 = 4
J0200 05 = 50 Parameter 11 - Setpoints J1103 01 = S2 J1106 03 = 3
J0200 06 = 100 J1100 00 = Off J1103 02 = S2.P J1106 04 = 4. J1403 00 = Off
J1100 01 = SP J1103 03 = S2.D J1106 05 = 5 J1403 01 = Co
Parameter 3 = Decimal Point J1101 00 = Off J1103 04 = S.P.D. J1106 06 = 6 J1403 02 = De
J0300 00 = 0 J1101 01 = S1 J1106 07 = 7
J0300 01 = 0.0 J1101 02 = S1.P J1104 00 = Pos J1106 08 = 8 J1404 00 = 3
J0300 02 = 0.00 J1101 03 = S1.D J1104 01 = Zer J1106 09 = 9 J1404 01 = 6
J0300 03 = 0.000 J1101 04 = S.P.D. J1106 10 = 10 J1404 02 = 12
J0300 04 = 0.0000 J1100 04 = Bat2 J1404 03 = 24
J1102 00 = Pos J1101 00 = Off Parameter 12 = Zero Band J1404 04 = 48
Parameter 5 = Digital Averaging J1102 01 = Zer J1101 01 = S1 J1200 00 = Off J1404 05 = 96
J0500 00 = 1 J1101 02 = S1.P J1200 01 = 1
J0500 01 = 2 J1103 00 = Off J1101 03 = S1.D J1200 02 = 2 J1405 00 = Off
J0500 02 = 4 J1103 01 = S2 J1101 04 = S.P.D. J1200 03 = 3 J1405 01 = Co
J0500 03 = 8 J1103 02 = S2.P J1200 04 = 4 J1405 02 = De
J0500 04 = 16 J1103 03 = S2.D J1102 00 = Pos J1200 05 = 5
J0500 05 = 32 J1103 04 = S.P.D. J1102 01 = Zer J1200 06 = 6 (J1406 for SI only)
J0500 06 = A1 J1103 05 = tol. J1200 07 = 7 J1406 00 = 3
J0500 07 = A2 J1103 00 = Off J1200 08 = 8 J1406 01 = 6
J1104 00 = Pos J1103 01 = 1 J1200 09 = 9 J1406 02 = 12
Parameter 6 = Tare J1104 01 = Zer J1103 02 = 2 J1200 10 = 10 J1406 03 = 24
J0600 00 = ATNR J1103 03 = 3 J1200 11 = 20 J1406 04 = 48
J0600 01 = Auto J1103 04 = 4. J1200 12 = 30 J1406 05 = 96
J0600 02 = FT J1103 05 = 5 J1200 13 = 40
Table 3-7. Configuration Setup Parameters