Yokogawa Single Channel Oxygen Analyzer System ZR22/ZR402 - Manual (Page 10)

ix
IM 11M12A01-03E
3.2 Installation of the Converter ........................................................................... 3-4
3.2.1 Location .................................................................................................. 3-4
3.2.2 Mounting of the Converter ...................................................................... 3-4
3.3 Installation of ZA8F Flow Setting Unit ......................................................... 3-7
3.3.1 Location ................................................................................................... 3-7
3.3.2 Mounting of ZA8F Flow Setting Unit .................................................... 3-7
3.4 Installation of ZR40H Automatic Calibration Unit ........................................ 3-9
3.4.1 Location ................................................................................................... 3-9
3.4.2 Mounting of ZR40H Automatic Calibration Unit .................................. 3-9
3.5 Installation of E7044KF Case Assembly for
the Calibration-gas Cylinder ......................................................................... 3-11
3.5.1 Location ................................................................................................. 3-11
3.5.2 Mounting ................................................................................................ 3-11
3.6 Insulation Resistance Test ............................................................................. 3-12
3.7 External Dimensions of Detectors with Pressure Compensation ................. 3-13
4. Piping ............................................................................................................................ 4-1
4.1 Piping for System 1 ........................................................................................ 4-1
4.1.1 Parts Required for Piping in System 1 ................................................... 4-2
4.1.2 Connection to the Calibration Gas Inlet ................................................. 4-2
4.1.3 Connection to the Reference Gas Inlet ................................................... 4-2
4.2 Piping for System 2 ........................................................................................ 4-3
4.2.1 Piping Parts for System 2 ........................................................................ 4-3
4.2.2 Piping for the Calibration Gas ................................................................ 4-4
4.2.3 Piping for the Reference Gas .................................................................. 4-4
4.3 Piping for System 3 ........................................................................................ 4-5
5. Wiring ........................................................................................................................... 5-1
5.1 General ............................................................................................................ 5-1
5.1.1 Terminals for the External Wiring in the Converter .............................. 5-3
5.1.2 Wiring ...................................................................................................... 5-3
5.1.3 Mounting of Cable Gland ........................................................................ 5-4
5.2 Wiring for Detector Output ............................................................................. 5-5
5.2.1 Cable Specifications ................................................................................ 5-5
5.2.2 Connection to the Detector ...................................................................... 5-6
5.2.3 Connection to the Converter ................................................................... 5-7
5.3 Wiring for Power to Detector Heater ............................................................. 5-8
5.3.1 Cable Specifications ................................................................................ 5-8
5.3.2 Connection to Detector ............................................................................ 5-8
5.3.3 Connection to Converter ......................................................................... 5-9
5.4 Wiring for Analog Output ............................................................................. 5-10
5.4.1 Cable Specifications .............................................................................. 5-10
5.4.2 Wiring Procedure ................................................................................... 5-10
5.5 Power and Grounding Wiring ....................................................................... 5-11
5.5.1 Power Wiring ......................................................................................... 5-11
5.5.2 Grounding Wiring ................................................................................. 5-11
5.6 Wiring for Contact Output ............................................................................ 5-12
5.6.1 Cable Specifications .............................................................................. 5-12
5.6.2 Wiring Procedure ................................................................................... 5-12
5.7 Wiring for ZR40H Automatic Calibration Unit ........................................... 5-13
5.7.1 Cable Specifications .................................................................................. 5-14
5.7.2 Wiring Procedure ...................................................................................... 5-14