Yokogawa EJX115A - Manual (Page 58)

<8. Diagnostic Information>
8-12
IM 01C25T04-01EN
ALARM
Display
Cause of
Alarm
AI1 Output Value (Channel = Primary Value) Totalizer Value (Channel = Calculate Value) NAMUR
NE107
Category
FSAFE_TYPE
= 0
FSAFE_TYPE
= 1
FSAFE_TYPE
= 2
FSAFE_TYPE
= 0
FSAFE_TYPE
= 1
FSAFE_TYPE
= 2
AL.93
AI MAN
AI1 block is
MAN mode
[Simulation
start]
UNCERTAIN:
Simulated
value, start
[Simulation
finished
(<10s)]
UNCERTAIN:
Simulated
value, end
[Simulation
finished
(10s<20s)]
GOOD(NC):
update event
[Simulation
start]
UNCERTAIN:
Simulated
value, start
[Simulation
finished
(<10s)]
UNCERTAIN:
Simulated
value, end
[Simulation
finished
(10s<20s)]
GOOD(NC):
update event
[Simulation
start]
UNCERTAIN:
Simulated
value, start
[Simulation
finished
(<10s)]
UNCERTAIN:
Simulated
value, end
[Simulation
finished
(10s<20s)]
GOOD(NC):
update event
GOOD (NC):
OK
GOOD (NC):
OK
GOOD (NC):
OK
C
AL.94
AI MAN
AI2 block is
MAN mode
GOOD (NC):
OK
GOOD (NC):
OK
GOOD (NC):
OK
AL.95
AI MAN
AI3 block is
MAN mode
AL.96
STB.SIM
Simulation
function of
Sensor TB is
active
[Simulation
start]
UNCERTAIN:
Simulated
value, start
[Simulation
finished
(<10s)]
UNCERTAIN:
Simulated
value, end
[Simulation
start]
UNCERTAIN:
Simulated
value, start
[Simulation
finished
(<10s)]
UNCERTAIN:
Simulated
value, end
[Simulation
start]
UNCERTAIN:
Simulated
value, start
[Simulation
finished
(<10s)]
UNCERTAIN:
Simulated
value, end
[Simulation
start]
UNCERTAIN:
Simulated
value, start
[Simulation
finished
(<10s)]
UNCERTAIN:
Simulated
value, end
[Simulation
start]
UNCERTAIN:
Simulated
value, start
[Simulation
finished
(<10s)]
UNCERTAIN:
Simulated
value, end
[Simulation
start]
UNCERTAIN:
Simulated
value, start
[Simulation
finished
(<10s)]
UNCERTAIN:
Simulated
value, end
AL.97
PB SIM
Simulation
function of
Physical block
is active
GOOD (NC):
OK
GOOD (NC):
OK
GOOD (NC):
OK
GOOD (NC):
OK
GOOD (NC):
OK
GOOD (NC):
OK
AL.72
TOT
MAN
Totalizer
Functiion block
is MAN mode
GOOD (NC):
OK
GOOD (NC):
OK
GOOD (NC):
OK
[Simulation
start]
UNCERTAIN:
Simulated
value, start
[Simulation
finished
(<10s)]
UNCERTAIN:
Simulated
value, end
[Simulation
finished
(10s<20s)]
GOOD(NC):
update event
[Simulation
start]
UNCERTAIN:
Simulated
value, start
[Simulation
finished
(<10s)]
UNCERTAIN:
Simulated
value, end
[Simulation
finished
(10s<20s)]
GOOD(NC):
update event
[Simulation
start]
UNCERTAIN:
Simulated
value, start
[Simulation
finished
(<10s)]
UNCERTAIN:
Simulated
value, end
[Simulation
finished
(10s<20s)]
GOOD(NC):
update event
C
AL.60
STB.
CFG
SENSOR
Transducer
block
configuration
Error
GOOD (NC):
OK
GOOD (NC):
OK
GOOD (NC):
OK
GOOD (NC):
OK
GOOD (NC):
OK
GOOD (NC):
OK
C