Yokogawa EJX118A Instruction Manuals and User Guides
We have 6 Instruction Manuals and User Guides for EJX118A Yokogawa
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 64 |
| Size: | 6.54 MB |
Show table of contents
Document Outline
- 1. Introduction
- 2. Handling Cautions
- 2.1 Model and Specifications Check
- 2.2 Unpacking
- 2.3 Storage
- 2.4 Selecting the Installation Location
- 2.5 Pressure Connection
- 2.6 Waterproofing of Cable Conduit Connections
- 2.7 Restrictions on Use of Radio Transceivers
- 2.8 Insulation Resistance and Dielectric Strength Test
- 2.9 Installation of an Explosion-Protected Instrument
- 2.10 EMC Conformity Standards
- 2.11 Pressure Equipment Directive (PED)
- 2.12 Low Voltage Directive
- 3. Component Names
- 4. Installation
- 5. Wiring
- 6. Operation
- 7. Maintenance
- 8. General Specifications
- Revision Information
| Recognized languages: | English |
|---|---|
| Pages: | 9 |
| Size: | 963 KB |
| Recognized languages: | English |
|---|---|
| Pages: | 96 |
| Size: | 10.60 MB |
Show table of contents
Document Outline
- 1. Introduction
- 2. Connection
- 3. Parameter Setting
- 3.1 Menu Tree
- 3.2 Basic Setup
- 3.3 Detailed Setup
- 3.3.1 Bi-directional Flow Measurement
- 3.3.2 Analog Output Signal Adjustable Range
- 3.3.3 Integral Indicator Display Mode
- 3.3.4 Integral Indicator Scale Setup
- 3.3.5 Unit for Displayed Temperature
- 3.3.6 Sensor Trim
- 3.3.7 Trim Analog Output
- 3.3.8 External Switch Mode
- 3.3.9 CPU Failure Burnout Direction and Hardware Write Protect
- 3.3.10 Software Write Protection
- 3.3.11 Signal Characterizer
- 3.3.12 Alarm
- 3.3.13 Status Output (only for EJX series: option code AL) 
- 3.3.14 Capillary Fill Fluid Density Compensation
- 3.3.15 Test Output, Simulation, and Squawk
- 3.3.16 Burst Mode
- 3.3.17 Multidrop Mode
- 3.3.18 Switching HART Protocol Revision
- 4. Diagnostics
- 4.1 Self-Diagnostics
- 4.2 Advanced Diagnostics(Only for EJX series) 
- 4.2.1 Multi-sensing Process Monitoring
- 4.2.2 Impulse Line Blockage Detection (ILBD)
- 4.2.2.1 Blockage Detection
- 4.2.2.2 Combination of Reference Result and Blockage Detection
- 4.2.2.3 Operation Parameters
- 4.2.2.4 Operating Procedure
- 4.2.2.5 Alarm and Alert Setting
- 4.2.2.6 Condition Check
- 4.2.2.7 Obtain Reference Values
- 4.2.2.8 Capability Test of Blockage Detection Operation
- 4.2.2.9 Start ILBD Operation
- 4.2.2.10 Tuning
- 4.2.2.11 Reset of Reference Value
- 4.2.2.12 ILBD Parameter List
- 4.2.3 Heat Trace Monitoring
- 4.3 Alarms and Countermeasures
- 5. Parameter Summary
- Appendix 1. Safety Instrumented Systems Installation
- Appendix 2. ILBD Check List
- Revision Information
| Recognized languages: | English |
|---|---|
| Pages: | 89 |
| Size: | 7.46 MB |
Show table of contents
Document Outline
- 1. Introduction
- 2. Handling Cautions
- 3. About PROFIBUS PA
- 4. Getting Started
- 5. Parameter Setting
- 6. Explanation of Basic Items
- 7. In-Process Operation
- 8. Diagnostic Information
- 9. Parameter Lists
- 10. General Specifications
- Appendix 1. List of DTM Menu
- Appendix 2. List of PDM (EDD) Menu
- Revision Information
| Recognized languages: | English |
|---|---|
| Pages: | 52 |
| Size: | 6.91 MB |
| Recognized languages: | English |
|---|---|
| Pages: | 41 |
| Size: | 3.65 MB |
Show table of contents
Document Outline
- 1. Introduction
- 2. Connection
- 3. Operation
- 3.1 BT200 Operating Procedures
- 3.2 Setting Parameters Using the BT200
- 3.2.1 Parameter Usage and Selection
- 3.2.2 Menu Tree
- 3.2.3 Setting Parameters
- (1) Tag No. Setup
- (2) Calibration Range Setup
- (3) Damping Time Constant Setup
- (4) Output Mode and Integral Indicator Display Mode Setup
- (5) Output Signal Low Cut Mode Setup
- (6) Integral Indicator Scale Setup
- (7) Unit Setup for Displayed Temperature
- (8) Operation Mode Setup
- (9) Impulse Line Connection Orientation Setup
- (10) CPU Failure Burnout Direction and Hardware Write Protect
- (11) Software Write Protect
- (12) Output Status Setup when a Hardware Error Occurs
- (13) Bi-directional Flow Measurement Setup
- (14) Range Change while Applying Actual Inputs
- (15) Sensor Trim
- (16) Test Output Setup
- (17) Signal Characterizer
- (18) Process Alarm
- (19) Status Output (option code AL)
- (20) Capillary Fill Fluid Density Compensation
- (21) Adjustment Information and User Memo Fields
- 3.3 Displaying Data Using the BT200
- 4. Self-diagnostics
- 5. Parameter Summary
- Appendix 1. Safety Instrumented Systems Installation
- Revision Information