Watlow Optimizing Your Process System with the Series 988 Controller - Manual (Page 71)

Optimizing Your Process System with the WATLOW Series 988
Index
8.3
process 2 5.2
process 2 prompt 3.7
process alarms 2.6, 3.7, 5.2
process input 6.2
process retransmit 6.3
process variable 2.9
product specifications 6.8
proportional band 2.4, 2.9, 3.2
proportional control mode 5.5
proportional derivative control
with manual reset 2.9
proportional-integral control 2.3
proportional-integral-derivative
(PID) 2.3
proportioning control
2.2, 2.9, 2.10
proportioning control with deriva-
tive 2.9
protocol 3.4
Q
QCD 3.3
QPAC 3.3
questions and answers 2.5
R
radio frequency interference 1.7
radio frequency noise 3.3
ramp rate 3.10
ramp to set point 1.3, 2.7, 3.10
ramping function prompt 3.10
range 2.5
range high 2 3.11, 3.13, 4.3
range high 2 prompt 3.7
range low 2 3.11, 3.13
range low 2 prompt 3.7
rate 2.3, 2.4, 2.10, 5.2
rate alarm 3.10
rate band 2.9
ratio control 1.8, 1.9,
2.7, 2.9, 4.7
read only 5.7
reference junction 2.10
relative humidity 3.8
remote set point 3.6, 3.11, 4.4
reset 2.4, 2.10
resistance temperature detector
(RTD) 2.5, 2.10, 6.2
retransmit 2.6, 2.10, 3.12
retransmit calibrate offset 3.12
retransmit high limit 3.12
retransmit low limit 3.12
retransmit options 3.11
RFI 3.3
RS-232 3.4, 5.5, 6.3
RS-422 1.9, 2.6, 3.4, 6.3
RTD 2.5, 2.10, 6.2
S
safety limits 2.6
SCR firing card 3.3
security 2.7, 5.7
semiconductor oven 3.3
sensor break 5.4, 6.8
sensor cost 2.5
sensor fails 5.6
sensor over-range error 5.6
sensor ranges 6.8
sensor under-range error 5.6
serial communications 3.4
serial number 5.5
serial port 3.4
Series 988/989 User’s Manual
6.6, 6.7
set point 3.10, 4.5
setup 3.4, 6.6
Setup menu 5.6, 5.7, 6.5, 6.6
ship date 5.5
shipping overseas 2.7
signal transmitter 2.5
silencing alarm 2.6, 5.3
sketch 7.1-7.11
slidewire feedback
1.4, 2.7, 2.10, 3.13, 6.2, 5.5
slidewire valve actuators 3.13
software features 7.6
software revision 5.5
solid-state output 2.6
solid-state relay 3.3, 6.3
spacing between controllers 2.6
specifications 6.8
square root extraction 3.9
SSR firing card 3.3
standard features 5.1-5.8, 7.7
start 3.10
startup 2.7, 6.6
switch PID sets 3.6
switched DC 5.5
switching sensitivity 2.10
system cycle time 2.4
system diagram 2.5
System menu 3.11, 5.7
system response time 2.4
system stress 2.7
system tuning 2.3
T
terminals 6.8
test chamber 3.4, 4.5
test output prompt 5.5
thermal lag 2.3
thermal system 2.10
thermocouple 2.10, 6.2
thermocouple only 5.5
three-mode control 2.10
three-way valve 4.6
time proportioning control 2.2,
2.10
transmitter power supply
2.10, 6.3
tune 3.2
Tuning of Industrial Control
Systems 2.4
tuning reference 2.4
tuning the system 2.4
U
UL 1.9, 2.7, 6.8
UL recognized 1.9
uncontrolled stream 4.7
universal millivolts 5.5
universal off 5.5
universal process types 5.5, 6.3
universal RTD 5.5
universal signal conditioner
3.9, 6.2
universal tc high gain 5.5
universal tc low gain 5.5
up-arrow key, see increment key
updates 2.5
upper display 6.5
urethane mixing 1.8
user's manual 6.7
V
vacuum 4.5
valve oscillations 3.13
variable-time-base 2.6, 2.8, 3.3
vertical configuration 7.8