Watlow Optimizing Your Process System with the Series 988 Controller - Manual (Page 70)

Optimizing Your Process System with the WATLOW Series 988
Index
8.2
fixed power output 5.6
flow transmitter 1.8, 3.9
form A relay 2.8, 5.2, 6.3
form A/B relay 5.5
form B relay 2.8, 5.2, 6.3
form C relay 2.9, 5.2, 5.5, 6.3
four dashes 5.6
front panel 2.7
front panel lockout 3.6
full lockout 5.7
G
gas valve 5.6
gas-fired furnace 3.13
gaskets 2.7
Global menu
3.6, 3.10, 4.4, 4.5, 4.7, 5.6, 5.7
ground counts 5.5
ground loops 2.5
H
hardware 7.8
heat-treat oven 3.12
heater current 1.2, 2.7, 3.3, 3.7
heater current transformer 6.2
horizontal version (989) 1.7, 7.8
hose-down 2.7
hunting 1.5, 2.9, 3.13
hysteresis 2.2, 2.9, 5.2
I
idle set point 3.6
idle temperature 3.6
increment key
3.11, 4.4, 5.6, 6.5
incubator 3.6
input 1 counts 5.5
input 1 linearization 3.9
input 2 counts 5.5
input 2 linearization 3.9
input 2 prompt 3.7, 3.11, 3.13
input devices 7.4
input errors 5.6
input filter 3.8
input linearization 2.9, 3.9
Input menu 3.7, 3.11
Input Table 6.2
inputs 2.5, 5.5, 6.8
integral 2.2, 2.4, 2.9, 2.10, 3.2
integration function 2.3
interactive process variables 2.7
interface prompt 3.4
internal percent 4.3
internal set point 4.2, 4.4
isolation 2.9
J
JIS 2.9
Joint Industrial Standards 2.9
K
keylock switch 5.7
keys 6.5
L
latching alarm 2.6, 5.2
learn high resistance value 3.13
learn low resistance value 3.13
LED 5.4, 5.5, 6.5
limits 1.7, 2.5, 2.6
linearization 2.9
local 3.11
local-remote prompt 3.11
lockout 3.6, 5.7
long lag times 4.2
long sensor lead 5.8
loop error detect 3.7
louver 1.4, 1.5
low-level contact 1.9
low-pass filter 3.8
lower display 6.5
M
manual mode 5.4, 5.6
manual tuning 2.3
master-remote 2.6, 3.11
mechanical relays 2.6
MODE key
3.6, 3.13, 5.5, 5.7, 6.5
model number 7.1
motorized valve 4.7
mounting 6.4, 6.6, 6.7
muffle furnace 3.10
multi-zone application 3.12
N
natural oscillation 2.4
NEMA 4X 2.7, 2.9, 6.8
no lockout 5.7
no module 5.5
noise immunity 2.5
non-latching alarm 2.6, 5.2
non-volatile checksum error 5.6
normally de-energized 5.2
normally energized 5.2
O
offset 2.4
ON/OFF control 2.2, 2.9
open collector 3.3, 6.3
open loop 2.2, 2.9, 5.4
open loop prompt 5.5
operating environment 6.8
operator interface 6.8
optimize 7.9
output 1 active 5.5
output 4 active 5.5
output devices 7.5
Output menu 3.12, 5.3
Output Table 6.3
outputs 2.5, 2.9, 5.5, 6.8
outputs, turn off 3.6
overshoot 2.3, 2.4, 2.9
P
P control 2.9
paint 4.7
panel cutouts 6.4
Panel Lockout menu 5.7
panel lockout prompt 5.5
part number 6.6
PD control 2.9
PDR control 2.7, 2.9
percent power output 5.4
percent power output (%OUT)
LED 6.5
personal computer 2.6
PI control 2.9
PID 2.2, 2.3, 2.7, 2.9,
2.10, 3.2, 4.2, 4.3, 4.5
PID A 4.3, 4.5
PID B 4.3, 4.5
PID menus 3.5
PLC 3.11
power 6.8, 7.7
power supply 5.5, 5.8, 7.8
pressure switch 4.5
process 2.2, 4.5, 5.5
process 1 5.2