beautypg.com

Operations, Chapter 3: operations pages, Control module operation page parameters – Watlow EZ-ZONE ST User Manual

Page 32

background image

Watlow EZ-ZONE

®

ST

30

Chapter 3 Operations Page

Chapter 3: Operations Pages

To go to the Operations Page from the Home Page,

press both the Up ¿ and Down ¯ keys for three sec-

onds. [``Ai] will appear in the upper display and
[oPEr]

will appear in the lower display.

• Press the Up ¿ or Down ¯ key to view available

menus. On the following pages top level menus

are identified with a yellow background color.

• Press the Advance Key

to enter the menu of

choice.

• If a submenu exists (more than one instance),

press the Up ¿ or Down ¯ key to select and then

press the Advance Key

to enter.

• Press the Up ¿ or Down ¯ key to move through

available menu prompts.

• Press the Infinity Key ˆ to move backwards

through the levels: parameter to submenu; sub-

menu to menu; menu to Home Page.

Press and hold the Infinity Key ˆ for two seconds

to return to the Home Page.

Control Module Operation Page Parameters

3

[``Ai]
[oPEr]

Analog Input Menu

[```1]
[``Ai]

Analog Input 1

[`Ain] Process Value

[`i;Er] Error Status

[`i;Ca] Calibration Offset

[`dio]
[oPEr]

Digital Input/Output Menu

[```1]
[`dio]

Digital Input/Output 1

[`do;S]

Output State

[`di;S]

Event State

[LiM]
[oPEr]

Limit Menu

[```1]
[LiM]

Limit 1

[`LL;S]

Low Set Point

[`Lh;S]

High Set Point

[Mon]
[oPEr]

Monitor Menu

[```1]
[Mon]

Monitor 1

[C;MA]

Control Mode Active

[`h;Pr]

Heat Power

[`C;Pr]

Cool Power

[`C;SP]

Closed Loop Working Set

Point

[`Pu;A]

Process Value Active

[Loop]
[oPEr]

Loop Menu

[```1]
[Loop]

Loop 1

[`C;M]

Control Mode

[A;tSP] Autotune Set Point

[`AUt] Autotune Request

[`C;SP] Closed Loop Set Point
[`id;S]

Idle Set Point

[`h;Pb]

Heat Proportional Band

[`h;hy]

Heat Hysteresis

[`C;Pb]

Cool Proportional Band

[`C;hy]

Cool Hysteresis

[``ti]

Time Integral

[``td]

Time Derivative

[``db]

Dead Band

[`o;SP]

Open Loop Set Point

[ALM]
[oPEr]

Alarm Menu

[```1]
[ALM]

Alarm 1

[`A;Lo]

Low Set Point

[`A;hi]

High Set Point

[CUrr]
[oPEr]

Current Menu

[```1]
[CUrr]

Current 1

[`C;hi]

High Set Point

[`C;Lo]

Low Set Point

[`CU;r]

Read

[`C;Er]

Error

[`h;Er]

Heater Error

[P;StA]
[oPEr]

Profile Status Menu

[```1]
[P;StA]

Profile Status 1

[P;Str]

Profile Start

[PACr]

Action Request

[`StP]

Active Step

[S;tyP]

Active Step Type

[t;SP1]

Target Set Point Loop 1

[P;SP1]

Produced Set Point 1

[hour]

Hours Remaining

[min] Minutes Remaining

[`sec] Seconds Remaining
[Ent1]

Active Event Output 1

[Ent2]

Active Event Output 2

[``JC]

Jump Count Remaining