FEC AFC1500 - Manual (Page 13)

7.2.2 Real-time display indication mode. 7-5
7.2.3 Fastening results display mode. 7-6
7.2.4 Parameter display mode 7-7
7.2.5 Parameter Data List 7-9
7.2.6 Status Display 7-22
7.3 Download / Setup Mode Operation. 7-23
7.3.1 Download Mode selection 7-23
7.3.2 Setup Mode selection 7-24
7.3.3 Parameter # Selection. 7-25
7.3.4 Data # selection 7-26
7.3.5 Data Edit Mode Operation 7-27
7.3.6 Parameter Copy 7-28
7.3.7 I/O Enable (Stand Alone or Multi Configuration) 7-29
7.3.8 Dual Transducer Set-up 7-30
Chapter 8: Maintenance and Inspection 8-1
8.1 Inspection Items 8-2
8.1.1 Nutrunner (Tool) 8-2
8.1.2 Spindle Assembly 8-2
8.1.3 Homerun cables 8-2
8.1.4 SAN unit 8-3
8.1.5 Air Handling Units (Air Conditioner, Heat Exchanger, etc.) 8-3
8.2 Basic operational tests 8-4
8.2.1 Torque transducer. 8-4
8.2.2 Resolver. 8-4
8.2.3 Motor. 8-4
8.2.4 Transmission Disassembly and Inspection 8-6
8.3 Replacements 8-9
8.3.1 SAN Unit Replacement 8-9
8.3.2 Replace Nutrunner (tool) 8-10
8.3.3 Replace Homerun cables 8-10
Chapter 9: Troubleshooting 9-1
9.1 Abnormal Conditions. 9-2
9.2 Torque Transducer Origin Error, Cal Check Error. 9-3
9.2.1 Code 1-0 Torque transducer / Zero Voltage error. 9-3
9.2.2 Code 1-1 Torque transducer / Cal Voltage error. 9-3
9.2.3 Code 1-2 Torque transducer / Zero check error. 9-3
9.2.4 Code 1-3 Torque transducer / Cal self-check error. 9-4
9.2.5 Code 1-4 Torque transducer / Started on Zero condition error. 9-4
9.2.6 Code 1-5 Torque transducer / Started on Cal condition error 9-4
9.2.7 Code 1-6 Torque transducer / Zero Level Self Check Error 9-4
9.3 Torque Over Abnormals 9-5
9.3.1 Code 2-0 Torque Over Abnormal / Offset Torque 9-5
9.3.2 Code 2-1 Torque Over Abnormal / Torque Inhibit High Limit 9-5
9.4 Tool EEPROM Errors 9-6
9.4.1 Code 3-0 Preamplifier / Tool ID Checksum error 9-6
9.4.2 Code 3-1 Preamplifier / Tool type error 9-6
9.4.3 Code 3-2 Preamplifier / Started without tool connected 9-6
9.4.4 Code 3-3 Preamplifier / Tool is not connected 9-6
9.5 System Memory Errors 9-7
9.5.1 Code 4-0 system memory error / Flash ROM write error 9-7
9.5.2 Code 4-1 system memory error / Flash ROM read error 9-7
9.5.3 Code 4-2 system memory error / Servo Amp Flash ROM error 9-7
9.6 Servo Amplifier Response / Resolver 9-8