Extron Electronics PowerCage FOX Tx_Rx HDMI User Guide User Manual
Page 31
Command and Response Table for Receiver SIS Commands (continued)
Command
ASCII Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
Video shutdown delay
NOTES:
•
The Set Video Delay command delays the digital video to help monitors sync correctly during an input rate change.
•
Only video is delayed. Embedded audio is not delayed.
Set delay
3*
X2)
#
Dly
X2)]
Delay video by an interval of
X2)
.
Example:
3*3#
Dly3
]
Delay video by an interval of 0.75 seconds
(3 x 0.25 seconds).
View delay
3#
X2)]
Switch and signal status requests
Request Audio switch status
E
Stat
}
EmbedAud
X2!]
Show the position of the Audio switch:
0 = off (embedded audio is muted) or 1 = on (unmute).
NOTE: The audio on the captive screw audio output always remains active regardless of the setting of this switch.
Check audio embed
E
5Stat
}
X1)]
Show if audio is embedded in the video stream:
0 = not detected or 1 = detected.
View link 1 (Tx-to-Rx) status
1S
X1)]
View link 2 (Rx-to-Tx) status
2S
X1)]
View input video status
3S
X1)]
View input audio status
4S
X1)]
View all signal status
5S
SigI
X1)
•
SigO
•
HdcpI
X1)
•
HdcpO
X1)]
Report the status of the HDMI input, HDMI output,
HDCP encoding on the input, and HDCP encoding
on the output.
View HDMI signal status
6S
SigI
X1)
•
SigO–
–
]
Report the status of the HDMI input and HDMI output
(always -- for a transmitter).
View HDCP status
7S
HdcpI
X1)
•
HdcpO
X1)]
Report the status of the HDCP encoding on the
input and HDCP encoding on the output.
View temperature
20S
X1!
F
•
X1!
C
]
Show temperature in degrees Fahrenheit and Celsius.
Information requests
Information request
I
1Lnk
X1)
•2Lnk
X1)
•Vid
X1)
•Aud
X1)
•
X1@
•Rx
]
The unit responds with the current status (signal
detected) of optical link 1, optical link 2, the
video input, and the audio link; the fiber optic
transmission mode (singlemode or multimode); and
the device type (Rx).
Show firmware version
Q
X1#]
Example:
Q
1.23
]
The factory-installed firmware version is 1.23 (sample
value only).
Request part number
N
70-889-nn
]
nn = 22 (singlemode) or 21 (multimode).
Resets
Reset memory presets
E
ZG
}
Zpg
]
Reset (erase) all memory presets.
System reset
E
ZXXX
}
Zpx
]
Reset all settings to factory defaults.
NOTE:
X(
= Mute and auto memory status
0 = off
1 = on
X2!
= Switch position
0 = off (right)
1 = on (left)
X1)
= Link status
0 = light or signal input not detected
1 = light or signal detected
X2)
= Video delay
0 = 0 second
(0 plus six steps at 0.25 seconds per step)
1 = 0.25 second
3 = 0.75 second
5 = 1.25 second
2 = 0.5 second (default) 4 = 1.0 second
6 = 1.5 second
X1#
= Firmware version
v.vv
X1!
= Internal temperature
nnnF•nnC
PowerCage FOX HDMI • Remote Control
25