Extron Electronics PowerCage FOX Tx_Rx HDMI User Guide User Manual
Page 27
Command and Response Table for Transmitter SIS Commands (continued)
Command
ASCII Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
Audio input gain and attenuation
NOTES:
•
The set gain (G) and set attenuation (g) commands are case sensitive. The increment level, decrement level, and show level are
not case sensitive.
•
When the controlling PC is connected to the receiver, the PowerCage FOX can perform this command only if the receiver-Tx-to-
transmitter-Rx fiber cable is connected. The unit returns the E14 error if the Rx fiber is not connected.
Set input audio gain to a
+dB value
X^
G
Aud
X&]
Set the input level to
X&
dB (gain).
Example:
2G
Aud+02.0
]
Set the input level to +2 dB (gain).
Set input audio attenuation
to a -dB value
X*
g
Au
d
X&]
Set the input level to
X&
dB (attenuation).
Increment input level
+G
Aud
X&]
Increase the audio level by 1 dB.
Example:
+G
Aud+03.0
]
Increment the input level from +2 dB to +3 dB.
Decrement input level
–G
Aud–01.0
]
Decrease the audio level from 0 dB to –1 dB.
Show input level
G
X&]
Plus mode transmission
NOTE: Plus mode forces the transmitter to emulate a PowerCage FOX DVI Plus or FOXBOX DVI Plus transmitter.
Enable Plus mode
81*1#
Plus1
]
Turn on Plus mode (default).
Disable Plus mode
81*0#
Plus0
]
Turn off Plus mode.
View Plus mode
81#
X(]
Show Plus mode status.
Input reports as an HDCP authorized device
HDCP authorized device on
E
E1HDCP
}
HdcpE1
]
Set the transmitter as an HDCP authorized device.
HDCP authorized device off
E
E0HDCP
}
HdcpE0
]
Set the transmitter as not an HDCP authorized device.
View HDCP authorized
device status
E
EHDCP
}
X(]
Show HDCP authorized device status.
Status requests
View link 1 (Tx-to-Rx) status
1S
X1)]
View link 2 (Rx-to-Tx) status
2S
X1)]
View input video status
3S
X1)]
View input audio status
4S
X1)]
View all signal status
5S
SigI
X1)
•
SigO
X1)
•
HdcpI
X1)
•
HdcpO
X1)]
Report the status of the HDMI input, HDMI output,
HDCP encoding on the input, and HDCP encoding
on the output.
View HDMI signal status
6S
SigI
X1)
•
SigO
X1)]
Report the status of the HDMI input and HDMI
output (always -- for a transmitter).
View HDCP status
7S
HdcpI
X1)
•
HdcpO
X1)]
Report the status of the HDCP encoding on the
input and HDCP encoding on the output.
View temperature
20S
X1!
F
•
X1!
C
]
Show temperature in degrees Fahrenheit and Celsius.
NOTE:
X^
= Audio gain adjustment range
00 to 10
X&
= Audio level adjustment range
-18 to +10 (in 1.0 dB steps)
X*
= Audio attenuation adjustment range
00 to 18
X(
= Enable or disable status
0 = off (down) or disable
1 = on (up) or enable
X1)
= Link and input status
0 = link or input not detected 1 = link or input detected
X1!
= Internal temperature
nnnF•nnC
PowerCage FOX HDMI • Remote Control
21