Extron Electronics IN1508 User Guide - Manual (Page 58)

Symbol Definitions
]
= CR/LF (carriage return/line feed)
}
= Carriage return (no line feed)
| = Pipe (can be used interchangeably with the
}
character)
•
= Space (hard) character
E
= Escape key (hex 1B)
W = Can be used interchangeable with the
E
character
X!
= Input number 1 through 8
X@
= Switcher resolution (EDID):
00 = Match output resolution (EDID only)
01 = 640 x 480 (VGA)
13 = 720p
02 = 800 x 600 (SVGA) 14 = 1080i
03 = 1024 x 768 (XGA) 15 = 1080p
04 = 1280 x 1024 (SXGA) 16 = 1280 x 768
05 = 1024 x 852 17 = 1440 x 900
06 = 1024 x 1024 18 = 1680 x 1050
07 = 1366 x 768 19 = 1280 x 800
08 = 1365 x 1024 20 = 852 x 480
09 = 1400 x 1050 21 = 1080p Sharp
10 = 1600 x 1200 (UXGA) 22 = 1920 x 1200
11 = 480p 23 = 1080p CVT
12 = 576p
X#
= Video refresh rate:
0 = Match output rate (EDID only)
1 = 50 Hz
3 = 75 Hz (24 Hz for 1080p)
2 = 60 Hz 4 = 59.94 Hz
X$
= On/off status (0 = off, 1 = on)
X%
= Lock (Exec. mode) status (0 [unlocked], 1 [partial], or 2 [full])
X^
= Picture adjustment range (000 through 128)
X&
= Horizontal shift range (000 through current horizontal output
resolution)
X*
= Vertical shift range (000 through current vertical output resolution)
X(
= Sharpness level (00 through 128)
X1)
= Horizontal start position (000 thru 200)
X1!
= Vertical start position (000 thru {variable})
X1@
= Pixel phase value (0 to 31)
X1#
= Gain value (numeric dB value, 0 to +9)
X1$
= Attenuation value (numeric dB value, –1 to –65)
X1%
= Gain/attenuation (–65 dB to +9 dB, each step = 1 dB)
X1^
= Output volume (0 to 100)
X1&
= Detected input signal standard (input 1 through 4 or 5):
0 = none 3 = NTSC 4.43
1 = NTSC 3.58 4 = SECAM
2 = PAL
X1*
= Input 5 video type:
0 = Interlaced component 2 = HDTV
1 = Progressive component
X1(
= PIP size:
00 = 1/4 (default) 03 = 1/25
01 = 1/9 04 = Side-by-side normal
02 = 1/16 05 = Side-by-side full screen
X2)
= Output video type:
0 = Y, B-Y, R-Y 2 = RGBS
1 = RGBHV 3 = RGsB
X2!
= Output sync polarity:
0 = H–/V– 2 = H+/V–
1 = H–/V+ 3 = H+/V+
X2@
= Aspect ratio (0 = 4:3, 1 = 16:9)
X2#
= Menu buttons:
00 = Menu 03 = Left
01 = Up 04 = Right
02 = Down 05 = Enter
X2$ = Pixel and line values (The range depends on the input resolution
applied and the output resolution selected).
X2% = Audio follow:
0 = Follow main window 2 = Toggle audio source
1 = Follow PIP window
X2^
= Window size (The range depends on the input resolution applied
and the output resolution selected).
X2&
= Test pattern:
0 = Off 2 = White field
1 = Alternating pixels 3 = Crop
IN1508 • Programming Guide 53