State, via sis command (see, Power save mode – Extron Electronics DVS 605 User Guide User Manual
Page 53
Command
ASCII Command
(host to scaler)
Response
(scaler to host)
Additional Description
Horizontal size (image)
Specific value
E
2*
X1*
*X1&HSIZ}
Hsiz2*X1**X1&]
Set horizontal sizing to
X1&
for image
X1*.
Increase width
E
2*
X1*
+HSIZ}
Hsiz2*X1**X1&]
Widen the image.
Decrease width
E
2*
X1*
-HSIZ}
Hsiz2*X1**X1&]
Make the image narrower.
View
E
2*
X1*
HSIZ}
X1& ]
View horizontal sizing value
X1&
for image.
Vertical size (image)
Specific value
E
2*
X1*
*X1&VSIZ}
Vsiz2*X1**X1&]
Set vertical sizing to
X1&
for image
X1*.
Increase height
E
2*
X1*
+VSIZ}
Vsiz2*X1**X1&]
Make the image taller.
Decrease height
E
2*
X1*
-VSIZ}
Vsiz2*X1**X1&]
Make the image shorter.
View
E
2*
X1*
VSIZ}
X1& ]
View vertical sizing value
X1&
for image.
Output Configuration
Output scaler rate
Set output rate
E
X1(
RATE}
RateX1(]
Select output resolution and refresh rate.
View output rate
E
RATE}
X1(]
Show selected output rate.
Output polarity (valid when VGA format is set to RGBHV)
Set polarity
E
X2!
OPOL}
OpolX2!]
Set polarity for VGA RGBHV ouput.
View polarity setting
E
OPOL}
X2!]
Show current output polarity.
VGA output sync format
Set format
EX2@
OSYN
}
Osyn
X2@]
Set output sync format of the VGA output.
View sync setting
E
OSYN
}
X2@]
Show current output sync format.
HDMI output format
Set format
E
X3^
VTPO}
VtpoX3^]
Set output color space/format
X3^
for the
HDMI output.
View setting
E
VTPO}
X3^]
Show current HDMI format.
Power save mode
Power save off
E
0PSAV}
Psav0]
DVS runs in full power mode (default).
Power save on
E
1PSAV}
Psav1]
DVS enters low power mode. Can only be
exited using
E
0PSAV}
command.
View setting
E
PSAV}
X4%]
View power save status.
NOTE:
X1& = Horizontal and vertical size: 0 to 11000
X1* = Image /window number: 1 = main window, 2 = PIP window
X1( = Scaler resolution/EDID emulation:
Examples: 1024x768/60, 720p/60, 1080p/60, 1920x1200/60.
on page 36 for full details.
X2! = Output polarity: 0 = H-/V- (default), 1 = H-/V+, 2 = H+/V-, 3 = H+/V+
X2@ = Output sync format: 0 = RGBHV (default), 1 = RGBS, 2 = RGsB, 3 = Y, R-Y, B-Y bi-level, 4 = Y, R-Y, B-Y tri-level
X3^ = HDMI output format:
0 = Auto (based on sink EDID), default
1 = DVI
2 = HDMI 444 RGB (0-255, audio, InfoFrames)
3 = HDMI 444 YUV “FULL” (0-255, audio, InfoFrames)
4 = HDMI 444 YUV “LIMITED” (16-235, audio, InfoFrames)
5 = HDMI 422 YUV “FULL” (0-255, audio, InfoFrames)
6 = HDMI 422 YUV “LIMITED” (16-235, audio, InfoFrames).
on page 38 for details.
X4% = Power save mode: 0 = full power mode (default), 1 = low power state
DVS 605 • SIS Communication and Control
47