Extron Electronics DVS 605 User Guide - Manual (Page 21)

Next
INx FORMAT
DIGITA
L
Rotate either to select input audio format.
*NOTE:
To activate the hidden menu “Edit Comms”,
press and hold input 5 and Next buttons simultaneously for three seconds.
To exit the Edit Comms menu press Menu.
Menu
ADVANCED
CONFIG
AUTO IMAGE
Input #x OF
F
Rotate to turn Auto Image mode on or off.
Next
Menu
SERIAL PORT
9600 RS23
2
DHCP MODE
On
MAC ADRESS 005A6078CEC
This is set at the factory and cannot be changed in “Edit Comm Settings” menu.
I 192.168 P 254.254 G 192.168 W 000.000 S 255.255 M 000.000 VIEW COMM SETTING
S
EXIT MENU? PRESS NEXT
Next Next Next Next Next Next
SERIAL PORT
9600 RS23
2
EDIT COMM SETTINGS
Rotate to select RS-232 mode. Rotate to change baud rate.
DHCP MODE
Rotate either to turn DHCP mode on or off.
Rotate to select octet field. Rotate to change IP address. Rotate to select octet field. Rotate to change Subnet address. Rotate to select octet field. Rotate to change Gateway address. Next Next Next Next Next
“Hidden” Menu *
TEST PATTER
N
COLOR BARS
Rotate either to change test pattern.
TEMPERATURE
96 F
35
C
FACT. RESET HOLD AUTO
Indicates internal temperature (not adjustable). Press and hold Auto button to reset unit to factory settings.
Next Next Next
SWITCH TYPE
DISSOLVE
Rotate either to change switch type.
Next
AUTO MEMORY
IN#x ON
Rotate either to turn auto memory on or off for selected input.
Next
ASPECT RATIO IN#x FILL
Rotate either to select aspect ratio mode.
Next
Rotate either to set volume level.
VOLUME -30d
B
Next
AUDIO MUT
E
ON
Next
INx GAIN/AT
T
0 dB
Rotate either to turn audio mute on or off. Rotate either to set gain and attenuation level.
Next
AUDIO CONFIG
PICTUR
E
CONTRO
L
(x)H POS
V
+00000+00000
Next
(x)BRIT CONT 064* *06
4
(x)COL TIN
T
064* *064
USER
PRESETS
INx RECAL
L
Next
Rotate either to select a preset to recall settings.
<02>
INx SAVE
Next
Rotate either to select a preset to save current settings to.
Menu
Menu
INPUT CONFIG
Rotate either to select input signal type.
INPUT #x
RGB
Next
(x)FILM MODE
OF
F
Rotate either to turn film mode off or to Auto.
Next
Next Next Next
Menu
Menu
(x)
DETAIL *064
(x)TPIX PHAS
1344* 01
Rotate to adjust total pixels (* = default). Rotate to adjust phase.
INx EDID
1600x1200@60
Rotate to set an EDID value for the active input.
Next Next
NOTE:
The Input Configuration submenus are
input specific and some menus may not be available depending on the input type.
RESOLUTION
1080p@6
0
Next
VGA FORMAT
RGBHV
Next
SYNC
H- V-
Rotate either to select the VGA format.
Next
OUTPUT CONFIG
Rotate to adjust brightness. Rotate to adjust contrast (* = default). Rotate to adjust color. Rotate to adjust tint (* = default). Rotate either to set detail level (* = default).
Next
(x)H SIZE
V
00000 00000
Rotate to adjust horizontal size. Rotate to adjust vertical size. Rotate to adjust horizontal position. Rotate to adjust vertical position.
Next
(x)H START
V
128 128
Rotate to adjust horizontal start. Rotate to adjust vertical start.
Next
(x)H ACT
V
1024* *0768
Rotate to adjust horizontal active pixels. Rotate to adjust vertical active pixels (* = default).
Rotate to select resolution. Rotate to select refresh rate Rotate either to set sync values. Next
HDMI FORMAT
AUTO
Rotate either to set HDMI format. Next
HDCP NOTE OFF
Rotate either to turn HDCP note on or off. Next
GENLOCK/AF
L
OFF Rotate either to set genlock mode.
Next
AUDIO OUTPUT
STEREO
Rotate either to select audio output format.
OVERSCAN
S-VIDEO 5.0%
Rotate either to set the overscan mode.
Next
I 192.168 P 254.254 S 255.255 M 000.000 G 192.168 W 000.000
Menu
NOTE:
Where used in this
flow chart “x” indicates the input number.
Next
H OFFSET
V
110 75
Rotate to adjust horizontal offset. Rotate to adjust vertical offset.
OSD DURATION
125 SEC
Rotate either to change OSD duration.
Next
IP address Gateway address
Subnet mask
Figur
e 10.
Main Menu
DVS 605 • Operation 15