Extron Electronics MAV Plus Series User Guide - Manual (Page 115)

Command and Response Table for IP- and Remote-Port-Specific SIS Commands (continued)
Command Function SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
IP and Remote port setup commands (continued)
Set e-mail events for recipient EX4! , X4# , X4$ , X4$ ,
...
, X4$ EM } You must first have set an e-mail
recipient for the e-mail account number
(
X4! ), using the separate Set e-mail (CR)
command (see the previous page).
Ipe X4%]
Example:
CrossPoint 450 Plus 3232 E 72,3,1,2,8,32,98,99,EM }
Ipe•[email protected] ]
E-mail account #72, JSmith, will
receive fail/missing and fixed/restored
messages for input signals 1, 2, 8, and
32; fans; and power supplies.
Read e-mail event notifications for
one account (recipient) EX4! EM } X4$ , X4$ , X4$ , ... , X4$]
Response description: Notify-what?,Inputs 1-32 (inputs above the matrix size are always zero),fans,PS ]
Example:
CrossPoint 450 Plus 3232 EX4! EM } See below
Response:
Notify failed and fixed
3, 1 1 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
01 Input: 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Fans
Power Supplies
E-mail input 8 status E-mail power supply and fan status Ignore input 16
0 0 0 0 0 0 0 0 1 1 1
Example: MAV Plus 1616 EX4! EM } See below
Response:
Notify failed and fixed
3, 1 1 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1
01 Input: 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 Power Supply
E-mail input 8 status Ignore input 16
Set DHCP on or off EX4^ DH } Idh X4^] Default: 0 (Off)
Read DHCP on/off status E DH } X4^]
Set serial port parameters EX4& * X4* , X4( , X5) , X5! CP }
Cpn X4& •Ccp X4* , X4( , X5) , X5!]
Read serial port parameters EX4& CP } X4* , X4( , X5) , X5!]
Configure flow control EX4& * X5$ , X8& CF ] Cpn X4& •Cfl X8^ , X5%]
Read flow control EX4& CF ] X5$ , X5%]
Configure receive timeout EX4& * X5^ , X8( CE ] Cpn X4& •Cce X8* , X5&]
Read receive timeout EX4& CE ] X5^ , X5&]
Set mode EX4& * X5@ CY } Cpn X4& •Cty X5@]
Read mode EX4& CY } X5@]
Set verbose mode EX5# CV } Vrb X5#]
Read verbose mode E CV } X5#]
Configure current port timeout E 0* X5* TC } Pti0* X5*]
Read current port timeout E 0TC } X5*]
Configure global IP port timeout E 1* X5* TC } Pti1* X5*]
Read global IP port timeout E 1TC } X5*]
Special Characters
The HTML language reserves certain characters for specific functions. The switcher does
not accept these characters as part of names, passwords, or locally created file names.
The switcher following characters are invalid or not recommended:
{space (spaces
are ok for names)} + ~ , @ = ‘ [ ] { } < > ’ “ semicolon (;) colon (:) |
\ and ?.
CrossPoint and MAV Series Matrix Switchers • Programming Guide 109