Extron Electronics MAV Plus Series User Guide User Manual
Page 114
X5#
= Verbose mode
0
= clear/none (default for Telnet connection)
1
= verbose mode (default for RS-232/RS-422 connection)
2
= tagged responses for queries
3
= verbose mode and tagged for queries
NOTE: If tagged responses is enabled (modes 2 and 3), all read commands return the constant string and the value as the set command
does (for example, the read matrix name command
E
CN
}
, returns Ipn•
X3!]
).
X5$
= Flow control
hardware, software, none (only the first letter required)
X5%
= Data pacing (in ms between bytes)
0000
(
default) -
1000
X5^
= Time (in 10 ms increments) to wait for characters
10
(= 100 ms, default) -
32767
X5&
= Time (in 10 ms increments) between characters
2
(= 20 ms, default) -
32767
X5*
= Port timeout interval (in 10-second increments)
1
(= 10 seconds) -
65000
(default is 30 = 300 seconds = 5 minutes)
SIS Command and Response Table for IP- and Remote Port-Specific Commands
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
IP and Remote port setup commands
Set matrix name
EX6!
CN
}
Ipn•
X3)]
Read matrix name (location)
E
CN
}
X3)]
Reset matrix name to factory default
E
•CN
}
Ipn•
X3!]
Set time and date
E
X3@
CT
}
Ipt
X3@]
Read time and date
E
CT
}
X3#]
Set GMT offset
EX3#
CZ
}
Ipz
X3#]
In the command, the divider between
hours and minutes can be either a
colon or a period. In the response, the
divider is a colon.
Example:
E
8.3CZ
}
Ipz+08:30
]
8.3 = 8:30
Read GMT offset
E
CZ
}
X3$]
Set Daylight Savings Time
EX3%
CX
}
X3%]
Read Daylight Savings Time
E
CX
}
X3%]
Set IP address
EX3^
CI
}
Ipi
X3^]
Default: 192.168.254.254
Read IP address
E
CI
}
X3^]
Read hardware address
E
CH
}
X3&]
Reads MAC address.
Read # of open connections
E
CC
}
X3*]
Set subnet mask
EX3^
CS
}
Ips
X3^]
Default: 255.255.0.0
Read subnet mask
E
CS
}
X3^]
Set gateway IP address
EX3^
CG
}
Ipg
X3^]
Default: 0.0.0.0
Read gateway IP address
E
CG
}
X3^]
Set administrator password
EX3(
CA
}
Ipa•
X3(]
Read administrator password
E
CA
}
X3(]
Reset (clear) administrator password
E
•CA
}
Ipa•
]
Set user password
EX3(
CU
}
Ipu•
X3(]
Read user password
E
CU
}
X3(]
Reset (clear) user password
E
•CU
}
Ipu•
]
Set mail server, domainname
EX3^
,
X4)
,
X3(
CM
}
Ipm
X3^
,
X4)
,
X3(]
Read mail server, domainname
E
CM
}
X3^
,
X4)
,
X3(]
Set e-mail recipient
EX4!
,
X4@
CR
}
Ipr
X4!
,
X4@
,
]
This command sets the recipient. To
receive e-mail notifications, you must then
set the events that the switcher reports,
using one or more separate Set e-mail
events (EM) commands (see the next
page).
Example:
E
}
Ipr72,[email protected]
,
]
Read e-mail recipient
EX4!
CR
}
X4@
,
X4$]
CrossPoint and MAV Series Matrix Switchers • Programming Guide 108