Wayne-Dalton 9100 - Manual (Page 17)

Tools Needed:
17
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com
INST
ALLA
TION
12
Power Drill
7/16” Socket
Driver
Vice Clamps
Phillips Head
Screwdriver TOP
SECTION
WITH OR
WITHOUT
U-BAR
ALIGN CENTER OF BOTH TABS WITH
CENTER LINE OF TOP SECTION
OPERATOR
BRACKET
U-BAR
TOP
SECTION
OPERATOR
BRACKET
MALE PART OF
TOP SECTION
(2) #12 X 1/2”
PHILLIPS HEAD
SCREWS
VICE CLAMP
NOTE: NOT REQUIRED
FOR J-STRUTS.
OPERATOR BRACKET
Operator Bracket
NOTE: Operator bracket must be
mounted and secured prior to installing
top section.
IMPORTANT: WHEN INSTALLING A
TROLLEY TYPE OPERATOR ON 9100,
9400, AND 9600 SERIES DOORS, A
WAYNE-DALTON TROLLEY BRACKET
MUST BE SECURELY ATTACHED TO
THE TOP SECTION, ALONG WITH ANY
U-BAR’S INITIALLY PROVIDED WITH THE
DOOR. IT IS THEN UNNECESSARY TO
FURTHER REINFORCE THE TOP SECTION
OF THE ABOVE MODEL WAYNE-DALTON
DOOR, WHEN ATTACHING A TROLLEY
TYPE OPERATOR, AS LONG AS THE
INSTALLATION OF THE OPERATOR
IS ACCORDING TO INSTALLATION
INSTRUCTIONS AND OWNER’S MANUAL
AND FORCE SETTINGS ARE ADJUSTED
PROPERLY.
Prior to installing top section, locate the
center of the top section and seat the
operator bracket on male part of the top
section. For retro fi t applications, the
operator bracket must be aligned with
an existing operator and positioned on
top section so it bridges the transition
point of the section thickness, as shown
in FIG. 1.1 and 1.2. Install (2) #12 x 1/2”
phillips head screws on the opposite
side of operator bracket, as shown in
FIG. 1.3. C
lamp operator bracket to u-bar
(if furnished), as shown in FIG. 1.4. First
attach (4) 1/4” - 14 x 5/8” self-tapping
screws to the operator bracket, as
shown in FIG. 1.5. Then attach (2) 1/4”
- 14 x 5/8” self-tapping screws to the
operator bracket, as shown in FIG. 1.6.
Remove vice clamps.
NOTE: If you have a 9100 door, (2) of the
1/4” - 20 x 11/16” self-drilling screws
used to attach the u-bar instead of (2)
1/4” - 14 x 5/8” self-tapping screws
when attaching operator bracket to u-
bar, as shown in FIG. 1.6.
NOTE: When attaching operator
bracket to top section with u-bar, apply
additional pressure to thread into the
u-bar.
NOTE: See
FIG. 1.7 for installing operator
bracket on top section without u-bars.
FIG. 1.1
FIG. 1.3
FIG. 1.5
FIG. 1.2
FIG. 1.4
FIG. 1.6
FIG. 1.7
OPPOSITE SIDE OF
OPERATOR BRACKET
(2) 1/4” - 20 X 11/16”
SELF-DRILLING SCREWS
OPERATOR
BRACKET
(2) 1/4” - 14 X 5/8”
SELF-TAPPING
SCREWS
(4) 1/4” - 14 X 5/8”
SELF-TAPPING
SCREWS
OPERATOR
BRACKET
OPERATOR
BRACKET
(6) 1/4” - 14 X 5/8”
SELF-TAPPING
SCREWS
U-BAR
U-BAR
U-BAR