Wayne-Dalton 9100 - Manual (Page 13)

13
Tools Needed:
Tools Needed:
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com
INST
ALLA
TION
Measure the length of the vertical tracks.
Using the jamb bracket schedule,
determine the placement of the jamb
brackets for your door height and track
type. To install the jamb brackets,
align the twistlock tab on the quick
install jamb bracket with the quick
install feature in the track and turn the
bracket perpendicular to the track so the
mounting fl ange is toward the back (fl at)
leg of the track.
Installing Q.I. Jamb Brackets
TOP
HOLE
BOTTOM
HOLE
MIDDLE
HOLE
JAMB BRACKET SCHEDULE
DOOR
HEIGHT
1ST SET 2ND SET 3RD SET
JAMB BKT POSITION JAMB BKT POSITION JAMB BKT POSITION
6’0” 64” TRACK
(1626 mm)
QIJB - 5 MIDDLE QIJB - 6 BOTTOM NOT APPLICABLE
6’5” 69” TRACK
(1753 mm)
QIJB - 3 BOTTOM QIJB - 6 MIDDLE NOT APPLICABLE
6’8” 72” TRACK
(1829 mm)
QIJB - 3 BOTTOM QIJB - 6 MIDDLE NOT APPLICABLE
7’0” 76” TRACK
(1930 mm)
QIJB - 3 BOTTOM QIJB - 7 TOP NOT APPLICABLE
7’3” 79” TRACK
(2007 mm)
QIJB - 3 BOTTOM QIJB - 5 BOTTOM QIJB - 6 BOTTOM
7’6” 82” TRACK
(2083 mm)
QIJB - 3 BOTTOM QIJB - 5 BOTTOM QIJB - 6 BOTTOM
7’9” 85” TRACK
(2159 mm)
QIJB - 3 BOTTOM QIJB - 5 BOTTOM QIJB - 6 BOTTOM
8’0” 4 SECTIONS
88” TRACK (2235 mm)
QIJB - 3 MIDDLE QIJB - 6 TOP QIJB - 7 MIDDLE
8’0” 5 SECTIONS
88” TRACK (2235)
QIJB - 3 BOTTOM QIJB - 7 TOP QIJB - 8 TOP
3RD SET HOLES
2ND SET HOLES
1ST SET HOLES
None
4
Drums
IMPORTANT: RIGHT AND LEFT HAND IS
ALWAYS DETERMINED FROM INSIDE THE
BUILDING LOOKING OUT.
NOTE: For door section identifi cation see
page 4.
TorqueMaster ® counterbalance drums
are marked right and left hand. Uncoil the
counterbalance cables and make sure you
place the right hand cable loop on the right
hand milford pin and place the left hand
cable loop on the left hand milford pin.
Insert a roller into bottom bracket of the
bottom section and insert another roller
at #1 end hinge at the top of the bottom
section. Repeat for other side.
NOTE: Verify astragal (bottom seal) is
aligned with door section. If there is more
than 1/2” excess astragal on either side,
trim astragal even with door section.
None
LEFT HAND TORQUEMASTER ®
COUNTERBALANCE DRUM
BOTTOM
SECTION
MILFORD PIN
#1 END HINGE
(HINGE TUBE)
BOTTOM BRACKET
BOTTOM
SECTION
ASTRAGAL
5
QUICK INSTALL FEATURE
QI JAMB BRACKET
TWISTLOCK TAB
LEFT SIDE SHOWN RIGHT SIDE SHOWN
COUNTERBALANCE
CABLE
ROLLERS
BOTTOM
SECTION