110 effects list lofi, Lofi noise, Slicer – Roland SH-32 User Manual
Page 110: Slicer sync (sync type), Tremolo, Tremolo sync (sync type)

110
Effects List
LOFI
This is an effect that intentionally degrades the sound quality for
creative purposes.
fig.LoFi
LOFI NOISE
In addition to a Lo-Fi effect, this effect also generates disc noise.
fig.LoFiNoise
SLICER
By applying successive cuts to the sound, this effect turns a
conventional sound into a sound that appears to be played as a
backing phrase. This is especially effective when applied to sustain-
type sounds. Divides each cycle into eight parts.
fig.Slicer
SLICER SYNC (Sync type)
Slicer synchronized to the BPM. Rate, set with INTENSITY, changes
according to the note length corresponding to the BPM setting.
How to Set the BPM Sync Start Timing (p. 112)
TREMOLO
Cyclically modulates the volume to add tremolo to the sound.
fig.Tremolo
TREMOLO SYNC (Sync type)
Tremolo synchronized to the BPM. Rate, set with INTENSITY,
changes according to the note length corresponding to the BPM
setting.
How to Set the BPM Sync Start Timing (p. 112)
Parameter
Value
Description
INTENSITY
(Cutoff)
200–8000 Hz
Reference frequency of the filter
COLOR
(LoFi Type)
1–9
Degrades the sound quality.
The sound quality grows poorer
as this value is increased.
RATE (DEPTH)
(Post Filter)
[OFF], [LPF],
[HPF]
Filter type after passing through
Lo-Fi
[OFF]:
no filter is used
[LPF]:
cuts the frequency range
above the Cutoff
[HPF]:
cuts the frequency range
below the Cutoff
* When set to [OFF], INTENSITY
has no effect.
LEVEL
(Post Gain)
0, +6, +12, +18 dB
Adjusts the output gain.
Parameter
Value
Description
INTENSITY
(Disc Noise Level)
0–127
Volume of the record noise
COLOR
(LoFi Type)
1–9
Degrades the sound quality.
The sound quality grows poor-
er as this value is increased.
RATE (DEPTH)
(Disc Noise Type)
[LP], [EP], [SP],
[rnd]
Type of record noise
The frequency at which the
noise is heard depends on the
selected type.
LEVEL
(Post Gain)
0, +6, +12, +18 dB
Adjusts the output gain.
Parameter
Value
Description
INTENSITY
(Rate)
0.05–10.0 Hz
Repeat rate
COLOR
(Pattern)
1–38
Slice pattern
RATE (DEPTH)
(Shuffle)
0–127
Timing of volume changes in levels for
even-numbered Beats
The higher the value, the later the beat
progresses.
LEVEL
(Attack)
0–127
Speed at which the volume changes
between beats
Lo-Fi
Post
Filter
L in
R in
L out
R out
Lo-Fi
Noise Gen.
L in
R in
L out
R out
L in
R in
L out
R out
Slicer
Slicer
Parameter
Value
Description
INTENSITY
(Rate)
Repeat rate
COLOR
(Pattern)
* Same as “SLICER”
RATE (DEPTH)
(Shuffle)
LEVEL
(Attack)
Parameter
Value
Description
INTENSITY
(Rate)
0.05–10.00 Hz
Frequency of the change
COLOR
(Wave Type)
[tri], [SqU], [Sin],
[SW1], [SW2]
Selects the way the volume is
modulated.
[tri]:
triangle wave
[SqU]:
square wave
[Sin]:
sine wave
[SW1/2]:
sawtooth wave
RATE (DEPTH)
(Depth)
0–127
Depth to which the effect is
applied
LEVEL
(EQ Gain)
-15– +15
+:
High boost
-:
Low boost
Parameter
Value
Description
INTENSITY
(Rate)
Frequency of the change
COLOR
(Wave Type)
* Same as “TREMOLO”
RATE (DEPTH)
(Depth)
LEVEL
(EQ Gain)
L in
R in
L out
R out
Tremolo
EQ
EQ
Tremolo
SW1
SW2