Roland JUNO-Di - Manual (Page 89)

89
Troubleshooting
Q When I play the keyboard, notes do not stop.
A
Is the pedal polarity of the Hold Pedal reversed?
Check the “Hold Pedal” “Polarity” parameter setting (p. 76).
Q There are some sounds I can’t select.
A If you use the included “JUNO-Di Editor” to set the patch’s category
to “NO ASSIGN,” you won’t be able to select it from the JUNO-Di’s
panel.
Q The sound cuts off when I switch tones (patches) in Patch
mode.
A
Although you can apply a wide variety of multi-effects with the
JUNO-Di’s multi-effects, switching the tone (patch) also switches the
type of multi-effects used.
In such instances, discrepancies between the sound being produced
and the multi-effects type can arise, which may result in sounds
being different than intended, so sounds produced when tones
(patches) are switched may be muted when factory settings are in
effect. In certain situations, such as when not using multi-effects
that have a great influence on the sound, remembering to set Patch
Remain parameter to “ON” allows you to switch Patches without
sounds being muted. Use the included “JUNO-Di Editor” to check
the Patch Remain setting.
Q When switching tones (patches) in Patch mode, the
volume and other parameters set with Control Changes
end up being reset.
A
Set Patch Remain parameter to “ON.” Even once they have switched
Patches, Control Change messages that have been received are
carried forward, so even when switching a tone (patch) whose level
is turned all the way down by a Control Change volume message,
the level remains unchanged. Use the included “JUNO-Di Editor” to
check the Patch Remain setting.
Q If the Tone Delay time value is set to the note, then does
the delay time not change beyond a fixed length when
the tempo is slowed down?
A
Use the included “JUNO-Di Editor” to check the following settings.
There is a maximum permissible value for the Tone Delay Time
parameter. So, if the time setting is specified in terms of a note
value, and the tempo is slowed down, this maximum permissible
value will be reached, and it cannot be increased further. The upper
time limit for each is the maximum value that can be set other than
the numerical value for the beat.
Q Even when I set the Pan for a tone (patch) completely to
one side, sound still comes from the other channel.
A The JUNO-Di’s internal effects are in stereo, so if you have effects
applied to a tone (patch), even if the Pan is set all the way to one
side, you will still be able to hear sounds of the effect component
from the other channel.
Q Sometimes, when playing legato, the pitch won’t rise.
A
Use the included “JUNO-Di Editor” to check the following settings.
When the Legato Switch parameter is “ON,” and the Legato
Retrigger parameter is “OFF,” and you hold down keys in the high
register to play legato, the upper pitch limit of the wave may be
exceeded, so that the pitch does not rise as far as you expect, but
will stop rising at a certain point. Additionally, if differing upper
pitch limits are used for the waves of a tone (patch) that uses
multiple tones, it may stop being heard in MONO. When making
large pitch changes, set the Legato Retrigger parameter to “ON.”
Q The notes sound strange in the upper registers of the
keyboard.
A
Sometimes when playing the keys in the upper part of the JUNO-
Di’s keyboard, the sound may stop, or the pitch may stop rising; or
with certain keys, there may be intermittent noise. This occurs
mainly when the JUNO-Di’s upper pitch limit is exceeded, so this
issue doesn’t arise in the ranges normally used. But, in any case, it
does not indicate a malfunction.
Q Although the same tone (patch) is selected, it sounds
different when I listen to it in the Performance.
A
Use the included “JUNO-Di Editor” to check the following settings.
In Performance mode, the parameters of each part of the
performance can apply further modification to parameters such as
pan, octave, and filter, relative to the settings specified by the patch.
Thus, tones (patches) in a Performance may sound different than
they do when heard in Patch mode.
Additionally, although a tone (patch) may comprise tones created
with the use of the multi-effects, the multi-effects used in the
Performance may differ from the multi-effects selected by the tone
(patch). Check the multi-effect settings of the performance. Also do
the same for the Chorus and Reverb settings.
Q I can’t play arpeggios.
The rhythm pattern won’t play.
A
Could the system setting “Sync Mode” (p. 76) be set to “SLAVE”?
If “Sync Mode” is set to “SLAVE,” the JUNO-Di needs to receive MIDI
clock messages from an external device.
You should leave “Sync Mode” set to “MASTER” unless you’re
synchronizing the JUNO-Di to an external device.
JUNO-Di_e.book 89 ページ ２００９年６月２２日 月曜日 午前９時２３分