Roland JUNO-Di User Manual
Page 76
76
Other Settings
HOLD
PEDAL
Assign
VIB-RATE,
VIB-DEPTH,
VIB-DELAY,
CHORUS-SEND,
REVERB-SEND,
AFTERTOUCH,
START/STOP,
TAP-TEMPO,
PROG-UP,
PROG-DOWN,
FAV-UP,
FAV-DOWN
VIB-RATE (CC76):
Vibrato speed
VIB-DEPTH (CC77):
Vibrato depth
VIB-DELAY (CC78):
Vibrato delay time
CHORUS-SEND (CC93):
The amount of the chorus
REVERB-SEND (CC91):
The amount of the reverb
AFTERTOUCH:
Channel aftertouch
START/STOP:
Pressing the pedal will start/stop the Song Player (p. 72) or Rhythm Pattern (p. 74).
TAP-TEMPO:
The tempo will be set to the interval at which you press the pedal (Tap Tempo).
PROG-UP:
If you’re playing a single sound, this selects the next sound. If you’re playing multiple sounds (i.e., when the
[PERFORM] button is lit), this selects the next-numbered performance.
PROG-DOWN:
If you’re playing a single sound, this selects the previous sound. If you’re playing multiple sounds (i.e.,
when the [PERFORM] button is lit), this selects the previous-numbered performance.
FAV-UP:
The favorite of the next number or bank will be selected.
FAV-DOWN:
The favorite of the previous number or bank will be selected.
Continuous
Hold
OFF, ON
If “Assign” is set to “HOLD,” turning this “ON” allows the HOLD PEDAL jack to support half-pedaling.
When this is set to support use of half-pedaling techniques, you can then connect an optional expression pedal (DP-10,
etc.), and employ pedal work to achieve even finer control in performances in which piano tones are used.
Polarity
STANDARD,
REVERSE
Selects the polarity of the pedal connected to the HOLD PEDAL jack.
On some pedals, the electrical signal output by the pedal when it is pressed or released is the opposite of other pedals. If
your pedal has an effect opposite of what you expect, set this parameter to “REVERSE.” If you are using a Roland pedal (that
has no polarity switch), set this parameter to “STANDARD.”
MIDI
Local Switch
OFF, ON
Determines whether the internal sound generator is disconnected (OFF) from the controller section (keyboard, pitch
bend/modulation lever, knobs, buttons, D Beam controller, pedal, and so on); or not disconnected (ON).
Normally this is left “ON,” but if you wish to use the JUNO-Di’s keyboard and controllers to control only external sound
modules, set it to “OFF.”
Patch Rx/Tx Ch
1–16
Tx Edit Data
OFF, ON
Specifies whether changes you make in the settings of a tone, performance will be transmitted as system exclusive
messages (ON), or will not be transmitted (OFF).
Soft Through
OFF, ON
If this is “ON,” incoming MIDI messages from the MIDI IN connector will be re-transmitted without change from the MIDI
OUT connector.
Sync Mode
MASTER, SLAVE
Specifies the synchronization message that the JUNO-Di will use for operation.
MASTER:
The JUNO-Di will be the master. Choose this setting when using the JUNO-Di by itself without synchronizing
to another device.
SLAVE:
The JUNO-Di will be the slave. Choose this setting when you want the JUNO-Di to synchronize to MIDI Clock
messages received from another MIDI device.
USB Driver
VENDER,
GENERIC
Sets the USB driver.
* This setting will take effect when you turn the power off, then on again.
MIC IN
SETTINGS
Rev Level
(Reverb Level)
0–127
Adjust the amount of reverb that is applied to the sound of the microphone.
Rev Type
(Reverb Type)
ROOM1, ROOM2,
STAGE1,
STAGE2,
HALL1, HALL2,
DELAY,
PAN-DELAY
Select the type of reverb/delay
ROOM1:
Short, high-density reflections
ROOM2:
Short, low-density reflections
STAGE1:
Greater amount of late reverberation
STAGE2:
Stronger early reflections
HALL1:
Clear-sounding reverberation
HALL2:
Rich-sounding reverberation
DELAY:
Conventional delay
PAN-DELAY:
Delay that moves the reflections between left and right
Rev Time
(Reverb Time)
0–127
Adjusts the length of the reverberation (when Rev Type is ROOM1–HALL2) or the delay time of the delay (when Rev Type
is DELAY or PAN-DELAY).
Mic Mode
ALL, VOCODER
MINUS
ONE
Parts to Mute
Part 1–Part16,
4&5, 1&4&5,
All except 10,
All except 2&10
Specifies the parts that will be muted by Minus One (p. 73) when playing back an SMF song. Parts for which this setting is
ON will be muted.
Part 1–Part16
: The specified part 1–16 will be muted.
4&5
: Parts 4 and 5 will be muted.
1&4&5
: Parts 1, 4, and 5 will be muted.
All except 10
: Parts other than part 10 will be muted. Normally, only the drums will be heard.
All except 2&10
: Parts other than parts 2 and 10 will be muted.
DBEAM
SETTINGS
D Beam Sens
0–127
This sets the D Beam controller’s sensitivity.
Increasing this value will make the D Beam controller more responsive.
POWER
SAVE
MODE
Time
OFF, 1min, 3min,
5min, 10min,
15min, 20min,
30min, 60min
Amount of idle time that is to pass before the JUNO-Di enters power-save mode.
When the JUNO-Di enters power-save mode, it will reduce its power consumption by turning off the display backlight and
minimizing button illumination.
Menu
Item
Value
Description
JUNO-Di_e.book 76 ページ ２００９年６月２２日 月曜日 午前９時２３分