Panasonic WJ-HD316 User Manual
Page 103
![background image](/manuals/181519/103/background.png)
103
The following are for the recording rate. When OFF is
selected, images from the selected camera channel will not
be recorded.
OFF/0.1 ips/0.2 ips/0.3 ips/0.4 ips/0.5 ips/1 ips/2 ips/3 ips/5
ips/6 ips/7.5 ips/10 ips/15 ips/30 ips/60 ips
AUTO: The recording rate will be set automatically. (Not
possible for event pre-recording and event post-record-
ing)
Important:
The total recording rates of each camera channels in
the same recording mode must be less than the record-
ing rate as described in "Recording Rate for Each
Recording Mode" above.
Examples: When selecting "FIELD" for resolution, "15
ips" for manual recording, "15 ips" for schedule
recording, "30 ips" for event recording:
Total recording rates of CAM 1 - 16 (manual recording):
less than 15 ips
Total recording rates of CAM 1 - 16 (schedule record-
ing): less than 15 ips
Total recording rates of CAM 1 - 16 (event recording):
less than 30 ips
When the total of the recording rates becomes more than
the set value, the recording mode table will turn red.
Recording mode table
The total recording rates between recording rates of event
pre-recording and recording rates of event post-recording
for each camera channel must be less than the recording
rate as described in "Recording Rate for Each Recording
Mode" above.
The following are available for the image quality.
SFA/SFB: Top quality (SUPER FINE)
FQA/FQB: High quality (FINE)
NQA/NQB: Standard quality (NORMAL)
EXA/EXB: Low quality (EXTENDED)
**A is suitable for less dynamic images.
**B is suitable for more dynamic images.
The following are available for the recording duration (only
event pre-recording and event post-recording).
1 s - 10 s (in 1 second intervals)
20 s/30 s/1 - 10 m (in 1 minute intervals)
20 - 60 m (in 10 minutes intervals)
MANUAL: The recording duration will be as follows
depending on the event type.
• At a motion detection: For 8 seconds
• At a video loss occurrence: During a video loss occur-
rence
• At a terminal alarm occurrence: During the supply of a
signal
• At a command alarm: For 8 seconds
CONTINUE: Recording will be performed continuously until
the ALARM RESET button is pressed.
w
[Event Prog] Create event programs for an
event occurrence
Perform the settings of event action for each event type
(motion detection, video loss, terminal/command alarm)
or of auto copy.
● VMD
Perform the settings of event action at a motion detection or
the settings of the auto copy function.
Perform the settings for the following action mode. Refer to
page xx for further information about each action mode.
ACT DET (Activity Detection Mode): Performs only
recording, writing an event log and camera movement
to a preset position at an event occurrence. Other event
actions will not be performed.
ALARM (Alarm Mode): Performs every event action
according to the settings.
Auto copy is the function to copy recorded images auto-
matically onto the copy area of the hard disk or the DVD-
RAM disk.
Select ON or OFF to enable or disable the auto copy func-
tion.
ON: Enable the auto copy function
OFF: Disable the auto copy function
Schedule
System
Display
Comm
Switcher
SETUP MENU
LIVE
Maintenance
Recording
Time Table
REC Prog
Event Prog
Special Days
Event
SETUP
SETUP
SETUP
SETUP
■
Recording Program 1
■
Recording Program 2
■
Recording Program 3
■
Recording Program 4
Schedule
System
Display
Comm
Switcher
SETUP MENU
LIVE
Maintenance
Recording
Time Table
REC Prog
Event Prog
Special Days
Event
SETUP
SETUP
SETUP
SETUP
■
Event Program 1
■
Event Program 2
■
Event Program 3
■
Event Action 4
Event PROG1
■
VMD
■
Video Loss
■
Terminal/Command Alarm
O K
CANCEL
SETUP
SETUP
SETUP
Event
Schedule
System
Display
Comm
Switcher
SETUP MENU
LIVE
Maintenance
Recording
Time Table
REC Prog
Event Prog
Special Days
SETUP
SETUP
SETUP
SETUP
■
Event Program 1
■
Event Program 2
■
Event Program 3
■
Event Program 4
■
Action Mode
■
Auto Copy
VMD
OK
ALARM
OFF
CANCEL