Panasonic WJ-NT204 - Manual (Page 120)

121
■ WJ-HD500 Digital Disk Recorder Control (Coax)
This is a system example that the WJ-NT204 transmitter has 4 of directly connected combination cameras while it has 12 of
combination cameras connected indirectly via the WJ-MP204 and WJ-HD500.
● Connections
1. Connect 4 combination cameras to VIDEO IN 1-4 on the WJ-NT204 with coaxial cables.
2. Connect VIDEO OUT 1-4 on the WJ-NT204 to VIDEO IN 1-4 on the WJ-HD500.
3. Connect MULTISCREEN OUT on the rear of the WJ-HD500 to VIDEO AUX IN on the WJ-NT204 with a BNC attached coax-
ial cable.
4. Connect 12 combination cameras to CAMERA IN 1-4 on WJ-MP204 unit #1 through #3 with coaxial cables.
5. Connect CAMERA OUT 1-4 on WJ-MP204 unit #1 through #3 to VIDEO IN 5-16 on the WJ-HD500.
6. Connect DATA terminals among WJ-MP204, WJ-HD500 and WJ-NT204 with RS-485 cables and branch connectors.
● Setup for Peripheral Devices
1. Address Setup
Unit addresses must be set as follow.
Unit Name Unit Address
WJ-HD500 1 (set in its own setup menu)
WJ-MP204 #1 2 (set with UNIT switch on its front panel)
WJ-MP204 #2 3 (set with UNIT switch)
WJ-MP204 #3 4 (set with UNIT switch)
2. Communication Parameter Setup
Every unit must be set to the same parameter in their own setup menus.
(For example, BAUD RATE: 9600 bps, DATA BIT: 8 bits, STOP BIT: 1 bit, PARITY: NONE)
3. Input Assignment
For WJ-MP204 units, open CAMERA CONFIG menu on each unit, and set CAM NO. (camera numbers) as follows.
Unit Name CAM NO.
WJ-MP204 #1 5CH through 8CH
WJ-MP204 #2 9CH through 12CH
WJ-MP204 #3 13CH through 16CH
For more information, refer to the manual included in each unit.
● Setup for WJ-NT204 Transmitter
1. On the ADMINISTRATOR SETUP PAGE, click the MODE SETUP button to open the MODE SETUP window.
2. Select either H.323/H.261 or JPEG in the MAIN PAGE DEFAULT MODE & INDEX FILE SELECT area.
Make the CONTROL SETUP as follows.
CAM CONTROL:
COAX
AUX SYSTEM CONTROL: HD500
Default Unit Address:
1
Click SET & REBOOT. The WJ-NT204 transmitter will restart. Confirm the transmitter has restarted.
3. On the ADMINISTRATOR SETUP PAGE, click the SERIAL PORT button to open the SERIAL PORT SETUP window.
In the window, select COAX for TYPE, and set communication parameters the same as that other devices are set to.
LINK/ 10BASE-T 100 BASE-TX CONNECT ACT
LOW HIGH
RING.VOL
Network Interface Unit WJ-NT
POWER ON OFF
LAN
MULTISCREEN OUT
AUX IN
WJ-HD500
5-8
Combination Camera 5-16
9-12 13-16
WJ-NT204
WJ-MP204
Browser
Browser
Browser
Browser
REMOTE
TIMER
OPERATE FULL HDD SEQUENCE
SET LOCK ALARM ALARM
RESET
ALARM SUSPEND MULTISCREEN SELECT
SETUP /ESC
GROUP
SELECT
SPOT
MULTISCREEN
DAYLIGHT SAVINGS
EL-ZOOM
COPY
REC PREVIEW INDEX
STOP BPLAY/ PAUSE REC
FWD REV
ALARM SEARCH
DISPLAY
REC STOP 1 2 3 4
13 14 15 16
9 10 11 12
5 6 7 8
Digital Disk Recorder
WJ-HD
FS 16
Ad 4 Ad 3 Ad 2
VIDEO OUT 1-4
VIDEO IN 1-4
VIDEO IN 5-16
VIDEO IN 1-4
Ad 1 DATA
CAMERA IN 1-4
CAMERA OUT 1-4
Note: Set DIP switch #3 on the rear of WJ-NT204 to ON.